Nissan Note E12. Manual — part 154
DLK-120
< REMOVAL AND INSTALLATION >
HOOD
CLEARANCE ADJUSTMENT
1. Loosen hood hinge nuts and bolts.
2. Loosen hood lock assembly bolts.
3. Adjust the hood lock assembly so the clearance measurements are within the specifications provided.
4. Tighten hood hinge nuts and bolts to specified torque.
5. Tighten hood lock assembly bolts to specified torque.
HEIGHT ADJUSTMENT
1. Loosen hood lock assembly bolts.
2. Adjust the surface height of hood assembly to front upper grille, front fender and front combination lamp to
the specified values by rotating hood bumper rubber.
3. Temporarily tighten hood lock assembly bolts.
4. Adjust (A) as shown to the following value with hood’s own weight by dropping it from approximately 200
mm (7.87 in) height or by pressing hood lightly [approximately 29 N (3.0 kg, 6.5 lb)].
5. After adjustment, tighten hood lock assembly bolts to specified torque.
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000009567332
REMOVAL
1. Remove hood assembly. Refer to
DLK-118, "HOOD ASSEMBLY : Removal and Installation"
2. Remove front fender. Refer to
DLK-125, "Removal and Installation"
3. Remove cowl top side cover. Refer to
.
4. Remove hood hinge bolts and hood hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Before installing the hood hinge, apply anticorrosive agent onto the surface of the vehicle.
C – C
H
Clearance
3.5
± 1.0 (0.14 ± 0.04)
1.5 (0.06)
1.5 (0.06)
J
Surface height
0.0
± 1.5 (0.0 ± 0.06)
1.5 (0.06)
1.5 (0.06)
Section
Item
Measurement
Standard
Parallelism
Equality
1.
Hood striker
2.
Secondary latch
3.
Primary latch
A.
20.0 mm (0.79 in)
ALKIA3162ZZ
HOOD
DLK-121
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check hood hinge rotating point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000009567333
REMOVAL
1. Support hood assembly using a suitable tool.
WARNING:
Bodily injury may occur if hood assembly is not supported properly when removing hood support
rod.
2. Rotate and remove hood support rod from grommet.
3. Release tab and remove grommet from hood hinge (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
JMKIA7995ZZ
DLK-122
< REMOVAL AND INSTALLATION >
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000009567334
RADIATOR CORE SUPPORT UPPER
RADIATOR CORE SUPPORT UPPER : Removal and Installation
INFOID:0000000009567335
REMOVAL
1. Remove front grille. Refer to
EXT-21, "Removal and Installation"
2. Remove ground harness bolt (A).
1.
Upper air guide
2.
Air guide (RH)
3.
Front bumper reinforcement
4.
Lower air guide
5.
Air guide (LH)
6.
Radiator core lower support
7.
Lower grommet
8.
Upper grommet
9.
Radiator core upper support
Clip
ALKIA3172ZZ
ALKIA3174ZZ
RADIATOR CORE SUPPORT
DLK-123
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Remove washer tube inlet clip (A).
4. Remove radiator cap adapter bracket bolt (A) and radiator reser-
voir tank bolt (B).
5. Remove horn. Refer to
HRN-6, "Removal and Installation"
6. Remove crash zone sensor. Refer to
SR-19, "Removal and Installation"
.
7. Remove hood lock assembly. Refer to
DLK-142, "HOOD LOCK : Removal and Installation"
.
8. Release hood lock release cable clips from radiator core support upper using a suitable tool.
9. Remove upper air guide. Refer to
10. Remove air guide (LH/RH). Refer to
.
11. Release all harness connector clips from radiator core support upper using a suitable tool.
12. Remove bolts (A) and radiator core support upper.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, perform hood assembly adjustment procedure. Refer to
RADIATOR CORE SUPPORT LOWER
RADIATOR CORE SUPPORT LOWER : Removal and Installation
INFOID:0000000009567336
REMOVAL
1. Remove radiator core support upper. Refer to
DLK-122, "RADIATOR CORE SUPPORT UPPER :
.
2. Reposition the radiator and condenser.
AWKIA2567ZZ
JMKIA8027ZZ
AWKIA2568ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст