Nissan Note E12. Manual — part 70
BR-16
< PERIODIC MAINTENANCE >
FRONT DISC BRAKE
CAUTION:
If the thickness is less than wear thickness + 0.3 mm (0.012 in), replace the disc brake rotor. Refer
BR-36, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
Thickness
Check the thickness of the disc brake rotor using a micrometer.
Replace the disc brake rotor if the thickness is below the wear limit.
Wear thickness
: Refer to
Wear thickness
: Refer to
.
Thickness variation (mea-
sured at 8 positions)
: Refer to
.
SBR020B
REAR DRUM BRAKE
BR-17
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
REAR DRUM BRAKE
BRAKE LINING
BRAKE LINING : Inspection
INFOID:0000000009364998
INSPECTION
Brake Lining
1. Remove plug from back plate. Refer to
2. Check brake lining wear thickness (A) from an inspection hole
on back plate. Check using a scale if necessary.
BRAKE LINING : Brake Burnishing
INFOID:0000000009671191
BRAKE BURNISHING
Burnish contact surfaces between brake lining and brake drum according to the following procedure after
refinishing brake drum, replacing brake drum, replacing brake lining, or if a soft pedal occurs at very low mile-
age:
CAUTION:
• Be careful of vehicle speed because the brake pedal does not operate firmly/securely until brake lin-
ing and brake drum are securely seated.
• Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1. Drive vehicle on straight, flat road.
2. Depress brake pedal with the power to stop vehicle within 3 to 5 seconds until the vehicle stops.
3. Drive without depressing brake pedal for a few minutes to cool the brake.
4. Repeat steps 1 to 3 until brake lining and brake drum are securely seated.
BRAKE DRUM
BRAKE DRUM : Inspection
INFOID:0000000009364999
INSPECTION
Appearance
Check surface of brake drum for uneven wear, cracks and serious damage. Replace it if necessary. Refer to
BR-40, "Removal and Installation"
.
NOTE:
• Make sure the parking brake control is fully released prior to removal of the brake drum.
Wear thickness
: Refer to
JSFIA1039ZZ
BR-18
< PERIODIC MAINTENANCE >
REAR DRUM BRAKE
• The rear wheel hub is part of the brake drum.
Brake Drum Inner Diameter
Check inner diameter (B) of the brake drum.
Inner diameter : Refer to
JPFIA0113ZZ
BRAKE PEDAL
BR-19
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
REMOVAL AND INSTALLATION
BRAKE PEDAL
Exploded View
INFOID:0000000009365000
NOTE:
The CVT brake pedal is shown. The M/T brake pedal is similar.
Removal and Installation
INFOID:0000000009365001
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-24, "Removal and Installation"
2. Remove knee bolster. Refer to
.
3. Disconnect the harness connector from the stop lamp switch.
4. Disconnect the harness connector from the ASCD cancel switch (if equipped).
5. Disconnect the harness connector from the accelerator pedal. Remove the accelerator pedal. Refer to
ACC-3, "Removal and Installation"
6. Separate the harness from brake pedal.
7. Rotate the stop lamp switch counter clockwise to remove.
8. Rotate the ASCD cancel switch (if equipped) counter clockwise to remove.
9. Remove snap pin and clevis pin from clevis.
10. Disconnect the power steering harness connector and position it aside.
11. Remove the brake pedal.
CAUTION:
Support the brake booster and master cylinder to prevent contact with other components.
1.
Snap pin
2.
Brake pedal
3.
Brake pedal pad
4.
Stop lamp switch
5.
Clip
6.
Clevis pin
7.
ASCD cancel switch (if equipped)
AWFIA0875GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст