Nissan Note E12. Manual — part 257
EM-28
< REMOVAL AND INSTALLATION >
[HR16DE]
INTAKE MANIFOLD
INTAKE MANIFOLD
Exploded View
INFOID:0000000009444848
Removal and Installation
INFOID:0000000009444849
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove air duct (inlet), air duct and air cleaner. Refer to
EM-26, "Removal and Installation"
.
2. Disconnect water hoses from the electric throttle actuator (if necessary).
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine coolant on the drive belt.
3. Remove electric throttle control actuator and position aside.
CAUTION:
• Handle carefully to avoid any shock to electric throttle control actuator.
• Do not disassemble electric throttle control actuator.
4. Disconnect EVAP purge control solenoid valve harness connector and vacuum hose from EVAP purge
control solenoid valve.
CAUTION:
Handle EVAP canister purge volume control solenoid valve carefully and avoid impacts.
1.
EVAP canister purge volume control
solenoid valve
2.
Hose clamp
3.
Vacuum hose
4.
PCV hose
5.
Hose clamp
6.
Intake manifold gasket
7.
Intake manifold
8.
Electric throttle control actuator
9.
Electric throttle control actuator
gasket
A.
To air duct
B.
To centralized under-floor piping
C.
To air duct
D.
To booster
E.
To PCV valve in rocker cover
Engine front
AWBIA1612ZZ
INTAKE MANIFOLD
EM-29
< REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
5. Disconnect vacuum hose for brake booster from intake manifold.
6. Remove intake manifold bolts (A) at the rocker cover.
7. Loosen bolts in reverse order as shown.
CAUTION:
Cover engine openings to avoid entry of foreign materials.
8. Remove intake manifold and intake manifold gasket.
9. Remove EVAP purge control solenoid valve from intake manifold (if necessary).
CAUTION:
Handle EVAP canister purge volume control solenoid valve carefully and avoid impacts.
INSTALLATION
Installation is in the reverse order of removal.
Intake Manifold
1. Install the new intake manifold gasket to the intake manifold.
• Align the protrusions used for checking gasket installation con-
dition with the clearance grooves (A) of the intake manifold
groove.
CAUTION:
Do not reuse the intake manifold gasket.
NOTE:
New gasket for electric throttle control actuator can be installed
when the electric throttle control actuator is installed.
2. Place the intake manifold into position.
CAUTION:
Check that the oil level gauge guide is not detached from the securing clip of the water inlet due to
interference of intake manifold.
AWBIA1620ZZ
AWBIA1576ZZ
JSBIA1220ZZ
EM-30
< REMOVAL AND INSTALLATION >
[HR16DE]
INTAKE MANIFOLD
3. Tighten the bolts to specification in the numerical order as
shown.
4. Tighten the intake manifold bolts (A) to specification at the
rocker cover.
Electric Throttle Control Actuator
1. Install electric throttle control actuator gasket to intake manifold.
CAUTION:
Do not reuse electric throttle control actuator gasket.
2. Tighten bolts of electric throttle control actuator equally and diagonally in several steps.
NOTE:
After installation, it is necessary to re-calibrate the electric throttle control actuator as follows:
• Perform “Throttle Valve Closed Position Learning” after repair when removing harness connector of the elec-
tric throttle control actuator. Refer to
.
• Perform “Throttle Valve Closed Position Learning” and “Idle Air Volume Learning” after repair when replacing
electric throttle control actuator. Refer to
AWBIA1576ZZ
Intake manifold bolts (A)
25.0 N·m (2.6 kg-m, 18 in-lb)
AWBIA1620ZZ
EXHAUST MANIFOLD
EM-31
< REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
EXHAUST MANIFOLD
Exploded View
INFOID:0000000009444850
Removal and Installation
INFOID:0000000009444851
REMOVAL
1. Remove air duct (inlet), air duct and air cleaner assembly. Refer to
.
2. Remove exhaust front tube. Refer to
3. Remove harness bracket from the cylinder head on the right rear side.
4. Remove exhaust manifold upper and lower covers.
5. Disconnect air fuel ratio sensor 1 harness connector.
6. Remove exhaust manifold side bolt of exhaust manifold stay.
AWBIA1603ZZ
1.
Exhaust manifold cover (upper)
2.
Harness bracket
3.
Air-fuel ratio sensor 1
4.
Exhaust manifold stay
5.
Heat insulator
6.
Exhaust manifold
7.
Exhaust manifold cover (lower)
8.
Exhaust maifold gasket
Engine front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст