Nissan Note E12. Manual — part 647
TM-146
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0705 TRANSMISSION RANGE SENSOR A
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Repair or replace malfunctioning parts.
10.
CHECK L POSITION SWITCH CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair or replace malfunctioning parts.
11.
CHECK L POSITION SWITCH CIRCUIT (PART 2)
1. Disconnect transmission position switch connector.
2. Turn ignition switch ON.
3. Check voltage between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Repair or replace malfunctioning parts.
12.
CHECK TRANSMISSION RANGE SWITCH
Check transmission range switch. Refer to
TM-146, "Component Inspection (Transmission Range Switch)"
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection (Transmission Range Switch)
INFOID:0000000009019925
1.
CHECK TRANSMISSION RANGE SWITCH
Check continuity between transmission range switch connector terminals.
+
−
Voltage
(Approx.)
TCM
Connector
Terminal
F44
6
Ground
0 V
TCM
Continuity
Connector
Terminal
F44
2
4
Not existed
5
6
7
+
−
Voltage
(Approx.)
TCM
Connector
Terminal
F44
2
Ground
0 V
Transmission range switch
Condition
Continuity
Terminal
7 – 10
Manual lever: “P” and “N” positions
Existed
Other than the above
Not existed
P0705 TRANSMISSION RANGE SENSOR A
TM-147
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to
250, "Removal and Installation"
4 – 5
Manual lever: “P” position
Existed
Other than the above
Not existed
4 – 8
Manual lever: “R” position
Existed
Other than the above
Not existed
4 – 9
Manual lever: “N position
Existed
Other than the above
Not existed
4 – 2
Manual lever: “D” position
Existed
Other than the above
Not existed
4 – 6
Manual lever: “L” position
Existed
Other than the above
Not existed
Transmission range switch
Condition
Continuity
Terminal
TM-148
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0706 TRANSMISSION RANGE SENSOR A
P0706 TRANSMISSION RANGE SENSOR A
DTC Logic
INFOID:0000000009019926
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Maintain the following conditions.
3. Shift the selector lever through entire positions from “P” to “L”. (Hold the selector lever at each position for
35 seconds or more.)
4. Check the first trip DTC.
Is “P0706” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009019927
1.
ADJUSTMENT OF CONTROL CABLE
Adjust control cable. Refer to
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn ignition switch ON.
2. Select “Self Diagnostic Results” in “TRANSMISSION”.
3. Touch “Erase”.
4. Perform "DTC CONFIRMATION PROCEDURE". Refer to
Is “P0706” detected?
YES
>> GO TO 3.
NO
>> INSPECTION END
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P0706
Transmission Range Sensor
A Circuit Range/Performance
All range signals stay OFF continuously for 30
seconds under the following diagnosis condi-
tion 1 and 2:
• Diagnosis condition 1 (continued for 30 sec-
onds or more)
- TCM power supply voltage: More than 11 V
• Diagnosis condition 2 (continued for 2 sec-
onds or more)
- Vehicle speed: Less than 3 km/h (2 MPH)
- Accelerator pedal position: 0.6/8 or less
- Idle switch: ON
- Stop lamp switch: ON
• Harness or connector
(Open circuit between ignition switch
and transmission range switch/open
circuit between transmission range
switch and TCM)
• Transmission range switch
• Control cable
Accelerator pedal position
: 0.0/8
Brake pedal
: Depressed
Vehicle speed
: 0 km/h (0 MPH)
P0706 TRANSMISSION RANGE SENSOR A
TM-149
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
CHECK POWER CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect transmission range switch connector.
3. Turn ignition switch ON.
4. Check voltage between transmission range switch harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 7.
4.
CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between transmission range switch harness connector terminals and TCM harness con-
nector terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 2)
Check continuity between transmission range switch harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning parts.
6.
CHECK TRANSMISSION RANGE SWITCH
Check transmission range switch. Refer to
TM-150, "Component Inspection (Transmission Range Switch)"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
+
−
Voltage
Transmission range switch
Connector
Terminal
F52
4
Ground
10 – 16 V
Transmission range switch
TCM
Continuity
Connector
Terminal
Connector
Terminal
F52
2
F44
4
Existed
5
7
6
6
8
6
9
5
Transmission range switch
—
Continuity
Connector
Terminal
F52
2
Ground
Not existed
5
6
8
9
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст