Nissan Note E12. Manual — part 358
GW-18
< REMOVAL AND INSTALLATION >
SIDE WINDOW GLASS
• This can be done by applying water to the side window glass area while pushing glass outward.
• To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
BACK DOOR WINDOW GLASS
GW-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
BACK DOOR WINDOW GLASS
Exploded View
INFOID:0000000009509414
Removal and Installation
INFOID:0000000009509415
REMOVAL
1. Remove high-mounted stop lamp. Refer to
EXL-117, "Removal and Installation"
2. Remove the back door inner finisher. Refer to
INT-34, "BACK DOOR INNER FINISHER : Removal and
.
3. Remove back door window glass using piano wire or power cutting tool (A) and an inflatable pump bag
(B).
• Mark the body and the glass with matching marks if the back door window glass is reused.
• Apply protective tape around the back door window glass to protect the painted surface from damage.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help pre-
vent glass splinters from entering your eyes or cutting your hands.
CAUTION:
1.
Back door window glass weatherstrip
2.
Back door window glass locator 3.
Back door window glass spacer
4.
Back door window glass
AWKIA2559ZZ
PIIB5779E
GW-20
< REMOVAL AND INSTALLATION >
BACK DOOR WINDOW GLASS
• Be careful not to scratch the glass when removing.
• Do not set or stand the glass on its edge. Small chips may develop into cracks.
• Apply protective tape around the back door window glass to protect the painted surface from
damage.
INSTALLATION
Installation is in the reverse order of removal.
• Use a genuine NISSAN Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
• Adhesive shall be continuously applied to assure watertightness. Glass installation shall be finished within
five minutes after applying the adhesive.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger compartment air pressure when a door is closed.
• The molding must be installed securely so that it is in position and leaves no gap.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
If affected by vapor inhalation, immediately move to an area with fresh air.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the back door window glass in case of an accident.
CAUTION:
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed
on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing time will increase
under lower temperatures and lower humidity.
REPAIRING WATER LEAKS FOR BACK DOOR WINDOW GLASS
• Leaks can be repaired without removing and reinstalling back door window glass.
• If water is leaking between the urethane adhesive material and body or glass, determine the extent of the
leak.
• This can be done by applying water to the back door window glass area while pushing glass outward.
• To stop the leak, apply primer (if necessary) and urethane adhesive to the leak point.
FRONT DOOR GLASS AND REGULATOR
GW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
FRONT DOOR GLASS AND REGULATOR
Exploded View
INFOID:0000000009509416
Removal and Installation
INFOID:0000000009509417
FRONT DOOR GLASS
Removal
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Remove the vapor barrier. Refer to
CAUTION:
Use care not to damage or tear vapor barrier during removal.
3. Disconnect the harness connector from the door mirror.
4. Temporarily reconnect both battery terminals and the main power window and door lock/unlock switch (LH
door) or power window and door lock/unlock switch (RH door) to raise/lower the front door glass until the
bolts can be seen through the access holes (with power window).
5. Temporarily reinstall the front door glass handle and raise/lower the front door glass until the bolts can be
seen through the access holes (without power window).
1.
Front door panel
2.
Vapor barrier
3.
Front door glass front run
4.
Front door glass rear run
5.
Front door glass
6.
Front door glass rubber run
7.
Front door regulator
8.
Front power window motor
9.
Front door glass handle grommet
10. Front door glass handle
A.
With power window
B.
Without power window
AWKIA2561ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст