Nissan Note E12. Manual — part 149
DLK-100
< SYMPTOM DIAGNOSIS >
IGNITION POSITION WARNING FUNCTION DOES NOT OPERATE
IGNITION POSITION WARNING FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000009516204
1.
CHECK POWER DOOR LOCK OPERATION
Check power door lock operation.
Does door lock/unlock with driver side door lock knob and door key cylinder?
YES
>> GO TO 2.
NO
>> Refer to
.
2.
CHECK DOOR SWITCH
Check door switch.
DLK-84, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-67, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
AUTO DOOR LOCK OPERATION DOES NOT OPERATE
DLK-101
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
AUTO DOOR LOCK OPERATION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000009516205
1.
CHECK AUTO LOCK SET SETTING IN WORK SUPPORT
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select AUTO LOCK SET in WORK SUPPORT mode.
3. Check AUTO LOCK SET setting in WORK SUPPORT.
BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set MODE 2, MODE 3, MODE 4, MODE 5, MODE 6 or MODE 7 in AUTO LOCK SET.
2.
REPLACE BCM
1. Replace BCM. Refer to
BCS-67, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
DLK-102
< SYMPTOM DIAGNOSIS >
VEHICLE SPEED SENSING AUTO LOCK OPERATION DOES NOT OPERATE
VEHICLE SPEED SENSING AUTO LOCK OPERATION DOES NOT OPER-
ATE
Diagnosis Procedure
INFOID:0000000009516206
1.
CHECK AUTOMATIC LOCK/UNLOCK SELECT SETTING IN WORK SUPPORT
1. Select DOOR LOCK of BCM using CONSULT.
2. Select AUTOMATIC LOCK/UNLOCK SELECT in WORK SUPPORT mode.
3. Check AUTOMATIC LOCK/UNLOCK SELECT setting in WORK SUPPORT.
BCS-17, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set Lock Only or Lock/Unlock in WORK SUPPORT.
2.
CHECK AUTOMATIC DOOR LOCK SELECT SETTING IN WORK SUPPORT
1. Select DOOR LOCK of BCM using CONSULT.
2. Select AUTOMATIC DOOR LOCK SELECT in WORK SUPPORT mode.
3. Check AUTOMATIC DOOR LOCK SELECT setting in WORK SUPPORT.
BCS-17, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set VH SPD in AUTOMATIC DOOR LOCK SELECT.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-67, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
DLK-103
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000009516208
1.
CHECK HAZARD ANSWER BACK SETTING IN WORK SUPPORT
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select HAZARD ANSWER BACK in WORK SUPPORT mode.
3. Check the HAZARD ANSWER BACK setting in WORK SUPPORT.
BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set the Lock Only, Unlock Only or Lock/Unlock in HAZARD ANSWER BACK.
2.
CHECK ANS BACK I-KEY LOCK SETTING IN WORK SUPPORT
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select ANS BACK I-KEY LOCK in WORK SUPPORT mode.
3. Check the ANS BACK I-KEY LOCK setting in WORK SUPPORT.
BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set the Horn Chirp or Buzzer in ANS BACK I-KEY LOCK.
3.
CHECK ANS BACK I-KEY UNLOCK SETTING IN WORK SUPPORT
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select ANS BACK I-KEY UNLOCK in WORK SUPPORT mode.
3. Check the ANS BACK I-KEY UNLOCK setting in WORK SUPPORT.
BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set the On in ANS BACK I-KEY UNLOCK.
4.
CHECK HAZARD FUNCTION
Check hazard function.
DLK-87, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
1. Replace BCM. Refer to
BCS-67, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст