Nissan Note E12. Manual — part 535
FRONT SEAT
SE-27
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
PASSENGER SIDE : Exploded View
INFOID:0000000009645123
PASSENGER SIDE : Seatback
INFOID:0000000009643081
DISASSEMBLY
1. Remove the passenger side front seat. Refer to
SE-16, "PASSENGER SIDE : Removal and Installation"
2. Remove the headrest.
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Slide finisher rear (LH/RH)
5.
Recline lever
6.
Seat cushion outer finisher (RH)
7.
Seat frame
8.
Seat cushion outer finisher (LH)
9.
Seat belt buckle
10. Seat cushion pad
11. Seat cushion trim
12. Seatback pad
13. Seatback trim
AWJIA1117ZZ
SE-28
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
3. Release trim strap (A) from the seat frame.
4. Release the J-hook retainer (C), unzip seatback zippers (A) and
release J-clips (B).
5. Release the headrest holder locks as shown and remove.
CAUTION:
Before removing the headrest holder, check its orientation
(front/rear and right/left).
6. Lift the seatback trim and seatback pad from the seat frame.
7. Remove the hog rings and separate the seatback trim (1) from
the seatback pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
ASSEMBLY
Assembly is in the reverse order of disassembly.
AWJIA0913ZZ
AWJIA1115ZZ
JMJIA4073ZZ
ALJIA0988ZZ
FRONT SEAT
SE-29
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat-
back trim and seatback pad wires.
• Smooth out all wrinkles during assembly.
• Use NISSAN standard hog rings and tools to assemble.
PASSENGER SIDE : Seat Cushion
INFOID:0000000009643082
DISASSEMBLY
1. Remove the passenger side front seat. Refer to
SE-16, "PASSENGER SIDE : Removal and Installation"
2. Remove snap ring (1) as shown (
) using a suitable tool, then
remove the recline lever (2).
3. Remove the seat cushion outer finisher (RH) (1).
a. Remove the screw (A).
b. Pull to release metal clips as shown (
) and remove.
: Metal clip
4. Remove seat belt buckle (RH). Refer to
SB-8, "FRONT SEAT BELT BUCKLE : Removal and Installation"
.
5. Remove the seat cushion outer finisher (LH) (2).
a. Remove seat cushion trim retainer (A).
b. Remove the screw (B).
c. Slide seat cushion outer finisher (LH) rearward as shown (
) to
release pawl and remove.
(1): Seat cushion trim
: Pawl
6. Remove the seat cushion trim and seat cushion pad from the seat frame.
PIIB3356J
AWJIA0907ZZ
AWJIA0917ZZ
AWJIA0918ZZ
SE-30
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
a. Remove trim strap (A) and J-hook retainers (B).
b. Remove the hog rings, then the seat cushion trim and seat
cushion pad from the seat frame.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
7. Remove the hog rings and separate the seat cushion trim (1)
from the seat cushion pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
cushion trim and seat cushion pad wires.
• Smooth out all wrinkles during assembly.
• Use NISSAN standard hog rings and tools to assemble.
AWJIA0919ZZ
AWJIA0923ZZ
ALJIA0990ZZ
PIIB3356J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст