Nissan Note E12. Manual — part 669
TM-234
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
KEY INTERLOCK CABLE
9. Lift lock plate (A) in the direction of the arrow (
C) and remove
in the direction of the arrow (
D).
10. Remove the key interlock cable from the key cylinder.
11. Disengage the clips and remove the key interlock cable from the
vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• Temporarily install the adjust holder (A) to the key interlock rod (B).
• Install the casing cap (C) to the cable bracket (D) on the shift
selector assembly.
CAUTION:
• Do not bend or twist key interlock cable excessively when
installing.
• After installing key interlock cable to cable bracket (D) on
shift selector assembly, make sure casing caps (C) is firmly
secured in cable bracket (D) on shift selector assembly.
• If casing cap (C) is loose [less than 39.2 N (4.0 kg, 8.8 lb)
removing force], replace key interlock cable.
• Slide the slider (A) toward the key interlock rod (D) while pressing
the pull lock (B) down to securely connect the adjust holder (C)
with the key interlock rod (D).
CAUTION:
• Do not press tabs when holding slider (A).
• Do not apply any side to side force to key interlock rod (D)
when sliding slider (A).
Inspection
INFOID:0000000009020025
INSPECTION AFTER INSTALLATION
• Check the CVT operation. If a malfunction is found, adjust the CVT position. Refer to
.
• Make sure the key can be removed only when the shift selector is in the “P” position.
• Make sure the ignition switch will not turn to LOCK position when the shift selector is not in the “P” position.
(1)
:Key interlock cable
(B)
:Key cylinder
JSDIA1798ZZ
JSDIA1799ZZ
JSDIA1800ZZ
TCM
TM-235
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
TCM
Exploded View
INFOID:0000000009020026
Removal and Installation
INFOID:0000000009020027
CAUTION:
When replacing TCM, note the “CVTF DETERIORATION DATE” value displayed on CONSULT “CON-
FORM CVTF DETERIORTN” in MAINTENANCE BOOKLET, before starting the operation.
NOTE:
When replacing the TCM and transaxle assembly as a set, replace the transaxle assembly first and then
replace the TCM. Refer to
REMOVAL
1. Remove the battery. Refer to
PG-69, "Removal and Installation (Battery)"
.
2. Disconnect the harness connector from the TCM.
3. Remove the TCM and bracket as an assembly.
4. Remove the TCM from the bracket (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
Adjustment
INFOID:0000000009020028
ADJUSTMENT AFTER INSTALLATION
Perform "ADDITIONAL SERVICE WHEN REPLACING TCM". Refer to
.
1.
TCM
2.
Bracket
3.
Clip
Front
AWBIA1482ZZ
TM-236
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
AIR BREATHER HOSE
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000009020029
REMOVAL
1. Remove air duct (inlet). Refer to
2. Remove air breather hose from transaxle assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that air breather hose is not collapsed or blocked due to folding or bending when installed.
• Be sure to insert air breather hose (1) fully until it reaches the
base of the transaxle tube (A).
JSDIA1978ZZ
G SENSOR
TM-237
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
G SENSOR
Exploded View
INFOID:0000000009020030
Removal and Installation
INFOID:0000000009020031
CAUTION:
• Do not drop or strike G sensor, because it may be damaged by impact.
• Do not use a power tool.
REMOVAL
1. Disconnect the battery negative terminal. Refer to
2. Remove center console. Refer to
IP-18, "Removal and Installation"
3. Disconnect the harness connector from G sensor.
4. Remove G sensor.
INSTALLATION
Installation is in the reverse order of removal.
Adjustment
INFOID:0000000009020032
ADJUSTMENT AFTER INSTALLATION
Perform “G SENSOR CALIBRATION”. Refer to
.
1.
G sensor
Front
JSDIA1922GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст