Nissan Note E12. Manual — part 308
EXL-100
< SYMPTOM DIAGNOSIS >
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
Description
INFOID:0000000009472919
Both side headlamps (LO) are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000009472920
1.
CHECK COMBINATION SWITCH
Check combination switch. Refer to
EXL-95, "WITH DAYTIME RUNNING LIGHT SYSTEM : Symptom Table"
(with DRL) or
EXL-94, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Symptom Table"
(without DRL).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “HL LO REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-67, "Removal and Installation"
3.
HEADLAMP (LO) CIRCUIT INSPECTION
Check headlamp (LO) circuit. Refer to
EXL-75, "Component Function Check"
Is the inspection result normal?
YES
>> Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL LO REQ
Lighting switch
2ND
On
OFF
Off
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON
EXL-101
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON
Description
INFOID:0000000009472921
The parking, license plate, side marker, tail lamps and each illumination are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000009472922
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
EXL-101, "Diagnosis Procedure"
.
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Replace BCM. Refer to
BCS-67, "Removal and Installation"
Monitor item
Condition
Monitor status
TAIL & CLR REQ
Lighting switch
1ST
On
OFF
Off
EXL-102
< SYMPTOM DIAGNOSIS >
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000009472923
The front fog lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000009472924
1.
CHECK FRONT FOG LAMP FUSE
1. Turn ignition switch OFF.
2. Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FRONT FOG LAMP SHORT CIRCUIT
1. Disconnect front fog connector and IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace fuse. (Replace IPDM E/R if the fuse is blown again.)
NO
>> Repair or replace harness. And then replace the fuse.
3.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning part.
4.
CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “FR FOG REQ” of IPDM E/R data monitor item.
2. With operating the front fog lamp switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 5.
NO
>> Replace BCM. Refer to
BCS-67, "Removal and Installation"
5.
FRONT FOG LAMP CIRCUIT INSPECTION
Check the front fog lamp circuit. Refer to
EXL-89, "Component Function Check"
.
Is the inspection result normal?
YES
>> Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace the malfunctioning part.
Unit
Fuse No.
Capacity
Front fog lamp
#31
15 A
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E46
71
No
LH
Monitor item
Condition
Monitor status
FR FOG REQ
Front fog lamp switch
(With lighting switch 2ND)
ON
On
OFF
Off
HEADLAMP AIMING ADJUSTMENT
EXL-103
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PERIODIC MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Inspection
INFOID:0000000009445897
PREPARATION BEFORE ADJUSTING
Before performing aiming adjustment, check the following:
• Ensure all tires are inflated to correct pressure.
• Place vehicle and screen on level surface.
• Ensure there is no load in vehicle other than the driver (or equivalent weight placed in driver's position).
• Coolant and engine oil filled to correct level, and fuel tank full.
• Remove cargo and/or luggage to maintain an unloaded vehicle condition.
• Confirm spare tire, jack and tools are properly stowed.
• Carefully wipe off any dirt from headlamp lens.
CAUTION:
Do not use organic solvent (thinner, gasoline etc.)
• Place a driver or equivalent weight of 68.5 kg (150 lb) on the driver seat.
• By hand, bounce the front and rear of the vehicle to settle the suspension and eliminate any static load.
• Place the front tires in the straight ahead position.
• Confirm headlamp aiming switch is set to "0" (zero) position.
• Aim each headlamp individually and ensure other headlamp beam pattern is blocked from screen.
NOTE:
• For headlamp aiming details, refer to regulations in your area.
• By regulation, no means for horizontal aim adjustment is provided from the factory; only vertical aim is
adjustable.
• Use adjusting screw to perform aiming adjustment.
• Perform headlamp aiming if:
- The vehicle front body has been repaired.
- The front combination lamp has been removed or replaced.
- Any outfitting has been installed.
- The vehicle’s standard load condition has been substantially increased.
AIMING ADJUSTMENT SCREW
AIMING ADJUSTMENT SCREW
AWLIA2171ZZ
A.
Headlamp (LH) (UP/DOWN)
adjustment screw
B.
Headlamp (RH) (UP/DOWN)
adjustment screw
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст