Nissan Pathfinder. Manual — part 1093
B0029 SIDE CURTAIN AIR BAG MODULE RH
SRC-57
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0029 SIDE CURTAIN AIR BAG MODULE RH
Description
INFOID:0000000009726801
DTC B0029 RH SIDE CURTAIN AIR BAG MODULE
The RH side curtain air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor
unit will monitor for opens and shorts in detected lines to the RH side curtain air bag module.
PART LOCATION
SRC-5, "Component Parts Location"
.
DTC Logic
INFOID:0000000009726802
With CONSULT
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.
CHECK SELF-DIAG RESULT
1. Turn ignition switch ON.
2. Check for DTC using CONSULT.
Is the DTC detected?
YES (Current DTC)>>Refer to
YES (Past DTC)>>GO TO 2.
NO
>> Inspection End.
2.
ERASE SELF-DIAG RESULT
Erase the DTC using CONSULT.
Can the DTC be erased?
YES
>> Inspection End.
NO
>> Refer to
DTC CONFIRMATION PROCEDURE (Without CONSULT)
1.
CHECK SELF-DIAG RESULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-16, "Trouble Diagnosis without CONSULT"
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009726803
1.
HARNESS CONNECTOR
Visually inspect all applicable harness connectors for the following:
CONSULT name
DTC
DTC detecting condition
Repair order
CURTAIN AIRBAG MODULE RH CIRCUIT
[OPEN]
B0029
RH side curtain air bag module circuit
is open.
CURTAIN AIRBAG MODULE RH CIRCUIT
[VB-SHORT]
RH side curtain air bag module circuit
is shorted to a power supply circuit.
CURTAIN AIRBAG MODULE RH CIRCUIT
[GND-SHORT]
RH side curtain air bag module circuit
is shorted to ground.
CURTAIN AIRBAG MODULE RH CIRCUIT
[SHORT]
RH side curtain air bag module cir-
cuits are shorted to each other.
SRC-58
< DTC/CIRCUIT DIAGNOSIS >
B0029 SIDE CURTAIN AIR BAG MODULE RH
• Visible damage to connector or terminal
• Loose terminal
• Poor connection
NOTE:
All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform one of the following repairs:
• Visible damage: Replace the harness.
• Loose terminal: Secure the terminal.
• Poor connection: Secure the connection.
2.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 3.
NO
>> Refer to
GI-49, "Intermittent Incident"
.
3.
WIRING HARNESS
Check the wiring harness for visible damage.
NOTE:
The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the harness.
4.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 5.
NO
>> Refer to
GI-49, "Intermittent Incident"
.
5.
AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace the air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 6.
NO
>> Clear DTC. Inspection End.
6.
SIDE CURTAIN AIR BAG MODULE RH
1. Replace the side curtain air bag module RH. Refer to
SR-22, "Removal and Installation"
.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 7.
NO
>> Clear DTC. Inspection End.
7.
RELATED HARNESS
Replace the related harness.
>> END
B0094 CRASH ZONE SENSOR
SRC-59
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0094 CRASH ZONE SENSOR
Description
INFOID:0000000009726810
DTC B0094 CRASH ZONE SENSOR
The crash zone sensor is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will
monitor for opens and shorts in detected lines to the crash zone sensor.
PART LOCATION
SRC-5, "Component Parts Location"
.
DTC Logic
INFOID:0000000009726811
With CONSULT
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.
CHECK SELF-DIAG RESULT
1. Turn ignition switch ON.
2. Check for DTC using CONSULT.
Is the DTC detected?
YES (Current DTC)>>Refer to
YES (Past DTC)>>GO TO 2.
NO
>> Inspection End.
2.
ERASE SELF-DIAG RESULT
Erase the DTC using CONSULT.
Can the DTC be erased?
YES
>> Inspection End.
NO
>> Refer to
DTC CONFIRMATION PROCEDURE (Without CONSULT)
1.
CHECK SELF-DIAG RESULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-16, "Trouble Diagnosis without CONSULT"
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected?
YES
>> Refer to
NO
>> Inspection End.
CONSULT name
DTC
DTC detecting condition
Repair order
CRASH ZONE SENSOR
[SENSOR FAIL]
B0094
Crash zone sensor has malfunctioned.
CRASH ZONE SENSOR
[COMM FAIL]
Crash zone sensor communication error.
CRASH ZONE SENSOR
[DISCONNECT]
Crash zone sensor is disconnected.
CRASH ZONE SENSOR
[UNMATCH]
Crash zone sensor is out of specification.
CRASH ZONE SENSOR
[GND-SHORT]
Crash zone sensor circuit is shorted to
ground.
SRC-60
< DTC/CIRCUIT DIAGNOSIS >
B0094 CRASH ZONE SENSOR
Diagnosis Procedure
INFOID:0000000009726812
1.
HARNESS CONNECTOR
Visually inspect all applicable harness connectors for the following:
• Visible damage to connector or terminal
• Loose terminal
• Poor connection
NOTE:
All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform one of the following repairs:
• Visible damage: Replace the harness.
• Loose terminal: Secure the terminal.
• Poor connection: Secure the connection.
2.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 3.
NO
>> Refer to
GI-49, "Intermittent Incident"
.
3.
WIRING HARNESS
Check the wiring harness for visible damage.
NOTE:
The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the harness.
4.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 5.
NO
>> Refer to
GI-49, "Intermittent Incident"
.
5.
CRASH ZONE SENSOR
1. Replace the crash zone sensor. Refer to
SR-23, "Removal and Installation"
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 6.
NO
>> Clear DTC. Inspection End.
6.
AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace the air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 7.
NO
>> Clear DTC. Inspection End.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст