Nissan Pathfinder. Manual — part 565
ENGINE MOUNT
EM-99
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
ENGINE MOUNT
ENGINE MOUNT (FRONT)
ENGINE MOUNT (FRONT) : Removal and Installation
INFOID:0000000009177939
WARNING:
• Situate the vehicle on a flat and solid surface.
• Place chocks at front and back of rear wheels.
CAUTION:
• Always work safely.
• Do not start work until the engine and exhaust system are cooled completely.
• Refer to the applicable sections for warnings, cautions, notes, and instructions if necessary proce-
dures are not included in this section.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the air cleaner case (upper), air cleaner case (lower), front air duct, and air duct hose and reso-
nator assembly. Refer to
EM-24, "Removal and Installation"
.
2. Remove the battery and battery tray assembly. Refer to
PG-92, "Removal and Installation"
3. Remove the engine under cover. Refer to
EXT-30, "Removal and Installation"
.
4. Remove the fender protector side covers (RH/LH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded
.
5. Partially remove the fender protectors (RH/LH). Refer to
EXT-28, "FENDER PROTECTOR : Removal and
.
6. Remove the radiator assembly. Refer to
CO-15, "Removal and Installation"
.
7. Remove the engine cooling fan shroud and motor assembly. Refer to
CO-17, "Removal and Installation"
.
8. Remove the exhaust manifold heat shield (LH). Refer to
.
9. Support the engine with a suitable tool.
10. Disconnect the engine mount insulator (front) vacuum hose.
11. Remove the engine mount insulator (front) nut (A).
12. Loosen the engine mount bracket (front) bolts in the reverse
order shown.
13. Remove the engine mount bracket (front).
AWBIA1241GB
: Engine front
JPBIA1731ZZ
EM-100
< REMOVAL AND INSTALLATION >
ENGINE MOUNT
14. Remove the engine mount insulator (front) bolts in the reverse
order as shown.
15. Remove the engine mount insulator (front).
INSTALLATION
CAUTION:
• Do not damage or spill engine oil on the engine mount insulator (front).
• Check engine mount insulator (front) is seated properly before tightening.
1. Install the engine mount insulator (front).
2. Install the engine mount insulator (front) bolts and tighten to
specification in the order shown.
3. Install the engine mount bracket (front) to the engine block.
: Front
JPBIA1735ZZ
AWBIA1242GB
AWBIA1242GB
: Front
Engine mount insulator (front)
bolts
: 55 N·m (5.6 kg-m,
41 ft-lb)
JPBIA1735ZZ
ENGINE MOUNT
EM-101
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4. Tighten the engine mount bracket (front) bolts to specification in
the order shown.
5. Install the engine mount insulator (front) nut (A) and tighten to
specification.
6. Installation of the remaining components is in the reverse order of removal.
: Engine front
Engine mount bracket (front)
bolts
: 40 N·m (4.1 kg-m,
30 ft-lb)
JPBIA1731ZZ
Engine mount insulator (front)
nut
: 103 N·m (11 kg-m,
76 ft-lb)
AWBIA1241GB
EM-102
< UNIT REMOVAL AND INSTALLATION >
ENGINE ASSEMBLY
UNIT REMOVAL AND INSTALLATION
ENGINE ASSEMBLY
2WD
2WD : Exploded View
INFOID:0000000009177940
2WD : Removal and Installation
INFOID:0000000009177941
WARNING:
• Situate the vehicle on a flat and solid surface.
• Place chocks at front and back of rear wheels.
• For engines not equipped with engine slingers, attach proper slingers and bolts described in PARTS
CATALOG.
CAUTION:
• Always work safely.
• Do not start work until the engine and exhaust system are cooled completely.
• Refer to the applicable sections for warnings, cautions, notes, and instructions if necessary proce-
dures are not included in the engine section.
AWBIA1639ZZ
1.
Gusset
2.
Rear torque rod
3.
Rear torque rod bracket
4.
Upper torque rod
5.
Engine mounting insulator (RH)
6.
Engine mounting bracket (RH)
7.
Engine mounting insulator (front)
8.
Engine mounting bracket (front)
9.
Vacuum hose
10. Vacuum tube (front)
11. Vacuum hose
12. Engine mounting insulator (LH)
13. Engine mounting insulator (rear)
14. Engine mounting bracket (rear)
15. Engine mounting stay (rear)
A.
To electronic controlled engine mount
control solenoid valve
B.
To transaxle
Front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст