Nissan Pathfinder. Manual — part 1022
SE-86
< REMOVAL AND INSTALLATION >
FRONT SEAT
Removal and Installation
INFOID:0000000009727772
REMOVAL
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seatback repair. It can lead to
personal injury if the side air bag module should accidentally deploy.
CAUTION:
• When removing or installing the seat trim, handle it carefully to keep dirt out and to avoid damage.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag module to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After front side air bag module inflates, the front seatback assembly must be replaced.
• When removing and installing the seat, use shop cloths to protect components from damage.
• Before removing the front seat, turn the ignition switch OFF, disconnect both battery cables then
wait at least three minutes.
1. Slide the seat to the full rearward position.
2. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
3. Disconnect the harness connector for side air bag module.
4. Remove the front slide finishers (LH/RH) (A) by lifting up and
then pulling forward, then remove the seat front bolts.
5. Connect the negative and positive battery terminals, then slide
the seat to the full forward position. Refer to
6. Disconnect negative and positive battery terminals, then wait at
least three minutes. Refer to
PG-90, "Removal and Installation"
7. Remove the rear slide finishers (LH/RH) (B) by lifting up and
then pulling rearward, then remove the seat rear bolts.
1.
Seat cushion trim
2.
Seat cushion pad
3.
Seat cushion inner finisher (RH)
(rear)
4.
Seat cushion inner finisher (RH)
(front)
5.
Recline lever finisher
6.
Seat cushion outer finisher (RH)
7.
Slide finisher outer (RH)
8.
Front slide finisher (RH)
9.
Front slide finisher (LH)
10. Seat frame assembly
11. Occupant Classification System
control unit (except Mexico)
12. Slide finisher outer (LH)
13. Seat cushion outer finisher (LH)
14. Seat belt buckle
15. Seat cushion inner finisher (LH)
(rear)
16. Seat cushion inner finisher (LH)
(front)
17. Rear slide finisher
18. Seat harness
19. Seatback board
20. Seatback assembly
21. Headrest holder (locked)
22. Headrest holder (free)
23. Headrest
ALJIA0787ZZ
FRONT SEAT
SE-87
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
8. Tilt the seat rearward and disconnect the harness connectors from the seat.
NOTE:
Take note of harness routing and attachment locations for correct installation.
9. Remove the seat from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
WARNING:
• Perform additional services when installing front passenger seat (except Mexico). Refer to
"ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"
.
• Zero point reset must be performed every time the front passenger seat is removed from the vehicle.
• Zero point reset is done after the front passenger seat is installed in vehicle and all bolts are tight-
ened to specification.
CAUTION:
Make sure that the seat harness or the floor carpet is not damaged during installation.
NOTE:
• When installing the front seat (LH), tighten the bolts in the order
shown.
• Tighten the seat bolts to specification. Refer to
.
• When installing the front seat (RH), tighten the bolts in the order
shown.
•
Tighten the seat bolts to specification. Refer to
.
Seatback Board
INFOID:0000000009727773
REMOVAL
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seatback repair. It can lead to
personal injury if the side air bag module should accidentally deploy.
CAUTION:
• When removing or installing the seat trim, handle it carefully to keep dirt out and to avoid damage.
• Before removing the front seat, turn the ignition switch OFF, disconnect both battery cables then
wait at least three minutes.
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
ALJIA0788ZZ
ALJIA0789ZZ
SE-88
< REMOVAL AND INSTALLATION >
FRONT SEAT
2. Release the two J-hook retainers (A) from the seatback frame.
3. Release the seatback board lower clips (B).
CAUTION:
Do not reuse seatback board lower clips.
4. Reach behind the seatback board and press the center clips (C)
inward and release from the seatback frame.
5. Pull the seatback board down releasing the upper clips (D) and
remove.
INSTALLATION
Installation is in the reverse order of removal.
Seatback Thermal Electric Device
INFOID:0000000009727774
REMOVAL
1. Remove the seatback board. Refer to
2. Release the seatback hook fastener straps (A).
3. Release the seatback J-clip retainers (B) holding the seatback
trim to the seatback frame.
4. Disconnect the harness connector (1) from the seatback thermal
electric device (2).
5. Remove the tie straps and seatback thermal electric device (2)
from the upper blower duct and seatback frame.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Do not reuse tie straps, new tie straps must be used for installation.
Seat Cushion Thermal Electric Device
INFOID:0000000009727775
REMOVAL
1. Remove the front seat. Refer to
SE-86, "Removal and Installation"
ALJIA0790ZZ
ALJIA0810ZZ
FRONT SEAT
SE-89
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
2. Remove the tie strap and lower blower duct (3) from the seat
cushion thermal electric device (2).
: Front
3. Disconnect the harness connector (1) from the seat cushion
thermal electric device (2).
4. Release the retaining clip and remove the seat cushion thermal
electric device (2) from the seat frame assembly.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Do not reuse tie straps, new tie straps must be used for installation.
Blower Motor Filter
INFOID:0000000009727776
REMOVAL
1. Remove the front seat. Refer to
SE-86, "Removal and Installation"
2. Release the J-hook retainers (A) from the seat frame assembly.
3. Remove the four screws and the seat cushion lower rear cover
(1) from the seat frame assembly.
4. Rotate the climate controlled blower motor filter (1) counter
clockwise and remove it from the blower motor (2).
Blower Motor
INFOID:0000000009727777
REMOVAL
1. Remove the front seat. Refer to
SE-86, "Removal and Installation"
ALJIA0811ZZ
ALJIA0791ZZ
ALJIA0792ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст