Nissan Pathfinder. Manual — part 207
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-17
< SYSTEM DESCRIPTION >
[BCM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
INT LAMP
INT LAMP : CONSULT Function (BCM - INT LAMP)
INFOID:0000000009174876
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF
→ ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a discharged battery and no-start condition.
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
NOTE:
The items listed below are the only applicable Work Support items for this vehicle. If other items are displayed
on CONSULT, do not use or change the setting for these other items.
TAIL LAMP SW [On/Off]
Indicates condition of combination switch.
FR FOG SW [On/Off]
Indicates condition of front fog lamp switch.
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH.
CDL LOCK SW [On/Off]
Indicates condition of lock signal from door lock and unlock switch.
Monitor Item [Unit]
Description
Test Item
Description
SEAT BELT WARN TEST
This test is able to check seat belt warning chime operation [On/Off].
LIGHT WARN ALM
This test is able to check light warning chime operation [On/Off].
REVERSE WARNING
This test is able to check reverse warning chime operation [On/Off].
ID REGIST WARNING
This test is able to check TPMS transmitter ID regist warning chime operation [On/Off].
Monitor Item [Unit]
Description
REQ SW -DR [On/Off]
Indicates condition of door request switch LH.
REQ SW -AS [On/Off]
Indicates condition of door request switch RH.
PUSH -SW [On/Off]
Indicates condition of push-button ignition switch.
UNLK SEN -DR [On/Off]
Indicates condition of door unlock sensor.
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH.
DOOR SW-AS [On/Off]
Indicates condition of front door switch RH.
DOOR SW-RR [On/Off]
Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off]
Indicates condition of rear door switch LH.
DOOR SW-BK [On/Off]
Indicates condition of back door switch.
CDL LOCK SW [On/Off]
Indicates condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW [On/Off]
Indicates condition of unlock signal from door lock and unlock switch.
KEY CYL LK-SW [On/Off]
Indicates condition of lock signal from door key cylinder switch.
KEY CYL UN-SW [On/Off]
Indicates condition of unlock signal from door key cylinder switch.
RKE-LOCK [On/Off]
Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off]
Indicates condition of unlock signal from Intelligent Key.
Test Item
Description
INT LAMP
This test is able to check interior room lamp operation [On/Off].
STEP LAMP TEST
This test is able to check step lamp operation [On/Off].
BCS-18
< SYSTEM DESCRIPTION >
[BCM]
DIAGNOSIS SYSTEM (BCM)
*: Initial setting
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEADLAMP)
INFOID:0000000009174877
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF
→ ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a discharged battery and no-start condition.
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
Support Item
Setting
Description
SCENARIO LIGHTING SETTING
On
NOTE:
Do not use this function since interior room lamp control is changed.
Off*
SET I/L D-UNLCK INTCON
On
Interior room lamp timer function ON.
Off*
Interior room lamp timer function OFF.
FOG LAMP OVERRIDE
On*
Fog lamp override function ON.
Off
Fog lamp override function OFF.
Monitor Item [Unit]
Description
PUSH SW [On/Off]
Indicates condition of push-button ignition switch.
ENGINE STATE [STOP/STALL/CRANK/
RUN]
Indicates engine status received from ECM on CAN communication line.
VEH SPEED 1 [km/h]
Indicates vehicle speed signal received from ABS on CAN communication line.
TURN SIGNAL R [On/Off]
Indicates condition of combination switch.
TURN SIGNAL L [On/Off]
TAIL LAMP SW [On/Off]
HI BEAM SW [On/Off]
HEAD LAMP SW 1 [On/Off]
HEAD LAMP SW 2 [On/Off]
PASSING SW [On/Off]
AUTO LIGHT SW [On/Off]
FR FOG SW [On/Off]
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH.
DOOR SW-AS [On/Off]
Indicates condition of front door switch RH.
DOOR SW-RR [On/Off]
Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off]
Indicates condition of rear door switch LH.
DOOR SW-BK [On/Off]
Indicates condition of back door switch.
OPTI SEN (DTCT) [V]
Indicates outside brightness voltage signal from optical sensor.
OPTI SEN (FILT) [V]
Indicates outside brightness voltage signal from optical sensor filtered by BCM.
Test Item
Description
FR FOG LAMP
This test is able to check front fog lamp operation [On/Off].
DAYTIME RUNNING LIGHT
This test is able to check daytime running lamp operation [On/Off].
ILL DIM SIGNAL
This test is able to check head lamp illumination dimming operation [On/Off].
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-19
< SYSTEM DESCRIPTION >
[BCM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
* : Initial setting
WIPER
WIPER : CONSULT Function (BCM - WIPER)
INFOID:0000000009174878
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF
→ ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a discharged battery and no-start condition.
DATA MONITOR
ACTIVE TEST
Support Item
Setting
Description
TWILIGHT ON
MODE2*
Autolamp function ON.
MODE1
Autolamp function OFF.
WIPER LINK
MODE4
This mode is not used.
MODE3*
Wiper link function operates in INT, LOW and HI.
MODE2
Wiper link function operates in LOW and HI.
MODE1
Wiper link function OFF.
CUSTOM A/LIGHT SETTING
MODE4
Less sensitive than normal setting (turns ON later).
MODE3
More sensitive than MODE2.
MODE2
More sensitive than normal setting (turns ON earlier).
MODE1*
Normal setting.
ILL DELAY SET
MODE 8
Autolamp delay timer.
MODE 7
MODE 6
MODE 4
MODE 5
MODE 3
MODE 2
MODE 1*
Monitor Item [Unit]
Description
PUSH SW [On/Off]
Indicates condition of push-button ignition switch.
VEH SPEED 1 [km/h]
Indicates vehicle speed signal received from ABS on CAN communication line.
FR WIPER HI [On/Off]
Indicates condition of wiper operation of combination switch.
FR WIPER LOW [On/Off]
FR WASHER SW [On/Off]
FR WIPER INT [On/Off]
FR WIPER STOP [On/Off]
Indicates front wiper auto stop signal received from IPDM E/R on CAN communication
line.
INT VOLUME [1
− 7]
Indicates condition of intermittent wiper operation of combination switch.
RR WIPER ON [On/Off]
Indicates condition of rear wiper operation of combination switch.
RR WIPER INT [On/Off]
RR WASHER SW [On/Off]
RR WIPER STOP [On/Off]
Indicates rear wiper motor auto stop input from rear wiper motor.
BCS-20
< SYSTEM DESCRIPTION >
[BCM]
DIAGNOSIS SYSTEM (BCM)
WORK SUPPORT
*
: Initial Setting
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER)
INFOID:0000000009174879
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF
→ ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a discharged battery and no-start condition.
DATA MONITOR
ACTIVE TEST
AIR CONDITIONER
AIR CONDITIONER : CONSULT Function (BCM - AIR CONDITIONER)
INFOID:0000000009174880
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF
→ ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a discharged battery and no-start condition.
DATA MONITOR
Test Item
Description
FR WIPER
This test is able to check front wiper operation [Hi/Lo/INT/Off].
RR WIPER
This test is able to check rear wiper operation [On/Off].
Support Item
Setting
Description
WIPER SPEED SETTING
On
Front wiper intermittent time linked with vehicle speed and wiper intermit-
tent dial position.
Off
*
Front wiper intermittent time is not linked with vehicle speed and wiper in-
termittent dial position.
Monitor Item [Unit]
Description
REQ SW -DR [On/Off]
Indicates condition of door request switch LH.
REQ SW -AS [On/Off]
Indicates condition of door request switch RH.
PUSH SW [On/Off]
Indicates condition of push-button ignition switch.
TURN SIGNAL R [On/Off]
Indicates condition of turn signal function of combination switch.
TURN SIGNAL L [On/Off]
HAZARD SW [On/Off]
Indicates condition of hazard switch.
RKE-LOCK [On/Off]
Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off]
Indicates condition of unock signal from Intelligent Key.
RKE-PANIC [On/Off]
Indicates condition of panic alarm signal from Intelligent Key.
Test Item
Description
FLASHER
This test is able to check turn signal lamp operation [Off/LH/RH].
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст