Nissan Pathfinder. Manual — part 1160

P0705 TRANSMISSION RANGE SENSOR A

TM-99

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0705 TRANSMISSION RANGE SENSOR A

DTC Logic

INFOID:0000000009177560

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Turn ignition switch ON.

2. Shift the selector lever through entire positions from “P” to “L”. (Hold the selector lever at each position for

5 seconds or more.)

3. Check the first trip DTC.
Is “P0705” detected?

YES

>> Go to

TM-99, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009177561

1.

CHECK TCM INPUT SIGNALS

With CONSULT

1. Turn ignition switch ON.

2. Select “Data Monitor” in “TRANSMISSION”.

3. Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, “P POSITION SW” and “L RANGE

SW”.

4. Shift the selector lever through entire positions from “P” to “L” and check ON/OFF of each monitor item.

Without CONSULT

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P0705

T/M RANGE SENSOR A
[Transmission Range Sensor
A Circuit (PRNDL Input)]

When all of the following conditions are satis-
fied and this state is maintained for 2 seconds:
• Two or more range signals simultaneously

stay ON continuously

• TCM power supply voltage: More than 11 V

• Harness or connector

(Short circuit between transmission
range switch and TCM)

• Transmission range switch

Monitor item

Condition

Condition

D POSITION SW

Selector lever: “D” position

On

Other than the above

Off

N POSITION SW

Selector lever: “N” position

On

Other than the above

Off

R POSITION SW

Selector lever: “R” position

On

Other than the above

Off

P POSITION SW

Selector lever: “P” position

On

Other than the above

Off

L POSITION SW

Selector lever: “L” position

On

Other than the above

Off

TM-100

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

P0705 TRANSMISSION RANGE SENSOR A

3. Turn ignition switch ON.

4. Shift the selector lever from “P” to “L” and check voltage between TCM harness connector terminals and

ground.

Is the inspection result normal?

YES >> Check

intermittent incident. Refer to

GI-49, "Intermittent Incident"

.

NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power

voltage.)]>>GO TO 2.

NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power

voltage.)]>>GO TO 4.

NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power

voltage.)]>>GO TO 6.

NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power

voltage.)]>>GO TO 8.

NO-5 [“L POSITION SW” is “ON” when selector is not in “L” position. (Or connector terminal 2 is at power

voltage.)]>>GO TO 10.

2.

CHECK D POSITION SW CIRCUIT (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK D POSITION SW CIRCUIT (PART 2)

1. Disconnect transmission range switch connector.

2. Turn ignition switch ON.

3. Check voltage between TCM harness connector terminal and ground.

+

−

Condition

Voltage

TCM

Connector

Terminal

F15

2

Ground

Selector lever: “ L” position

10 – 16 V

Other than the above

Approx. 0 V

4

Selector lever: “D” position

10 – 16 V

Other than the above

Approx. 0 V

5

Selector lever: “N” position

10 – 16 V

Other than the above

Approx. 0 V

6

Selector lever: “R” position

10 – 16 V

Other than the above

Approx. 0 V

7

Selector lever: “P” position

10 – 16 V

Other than the above

Approx. 0 V

TCM

Continuity

Connector

Terminal

F15

4

2

Not existed

5

6

7

P0705 TRANSMISSION RANGE SENSOR A

TM-101

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

4.

CHECK N POSITION SW CIRCUIT (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK N POSITION SW CIRCUIT (PART 2)

1. Disconnect transmission range switch connector.

2. Turn ignition switch ON.

3. Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

6.

CHECK P POSITION SW CIRCUIT (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace malfunctioning parts.

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F15

4

Ground

0 V

TCM

Continuity

Connector

Terminal

F15

5

2

Not existed

4

6

7

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F15

5

Ground

0 V

TCM

Continuity

Connector

Terminal

F15

7

2

Not existed

4

5

6

TM-102

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

P0705 TRANSMISSION RANGE SENSOR A

7.

CHECK P POSITION SW CIRCUIT (PART 2)

1. Disconnect transmission range switch connector.

2. Turn ignition switch ON.

3. Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

8.

CHECK R POSITION SW CIRCUIT (PART1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Repair or replace malfunctioning parts.

9.

CHECK R POSITION SW CIRCUIT (PART 2)

1. Disconnect transmission range switch connector.

2. Turn ignition switch ON.

3. Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

10.

CHECK L POSITION SWITCH CIRCUIT (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between TCM harness connector terminals.

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F15

7

Ground

0 V

TCM

Continuity

Connector

Terminal

F15

6

2

Not existed

4

5

7

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F15

6

Ground

0 V