Nissan Pathfinder. Manual — part 249
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
BRC-55
< BASIC INSPECTION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Description
INFOID:0000000009177267
Refer to the table below to determine if adjustment of steering angle sensor neutral position is required.
×: Required –: Not required
Work Procedure
INFOID:0000000009177268
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
CAUTION:
To adjust neutral position of steering angle sensor, make sure to use CONSULT.
(Adjustment cannot be done without CONSULT).
1.
ALIGN THE VEHICLE STATUS
Stop vehicle with front wheels in straight-ahead position.
>> GO TO 2.
2.
PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR
1. On the CONSULT screen, touch “WORK SUPPORT” and “ST ANG SEN ADJUSTMENT” in order.
2. Touch “START”.
CAUTION:
Do not touch steering wheel while adjusting steering angle sensor.
3. After approximately 10 seconds, touch “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4. Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3.
3.
CHECK DATA MONITOR
1. Run vehicle with front wheels in straight-ahead position, then stop.
2. Select “DATA MONITOR”. Then make sure “STR ANGLE SIG” is within 0
±2.5°.
Is the steering angle within the specified range?
YES
>> GO TO 4.
NO
>> Perform the neutral position adjustment for the steering angle sensor again, GO TO 1.
4.
ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
Situation
Adjustment of steering angle sensor neutral position
Removing/Installing ABS actuator and electric unit (control unit)
—
Replacing ABS actuator and electric unit (control unit)
×
Removing/Installing steering angle sensor
×
Replacing steering angle sensor
×
Removing/Installing steering components
×
Replacing steering components
×
Removing/Installing suspension components
×
Replacing suspension components
×
Change tires to new ones
—
Tire rotation
—
Adjusting wheel alignment
×
Battery disconnection
×
BRC-56
< BASIC INSPECTION >
[VDC/TCS/ABS]
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
• ABS actuator and electric unit (control unit): Refer to
• ECM: Refer to
Are the memories erased?
YES
>> Inspection End.
NO
>> Check the items indicated by the self-diagnosis.
CALIBRATION OF DECEL G SENSOR
BRC-57
< BASIC INSPECTION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
CALIBRATION OF DECEL G SENSOR
Description
INFOID:0000000009177269
Refer to the table below to determine if calibration of the decel G sensor is required.
×: Required –: Not required
Work Procedure
INFOID:0000000009177270
CALIBRATION OF DECEL G SENSOR
CAUTION:
To calibrate the decel G sensor, make sure to use CONSULT.
(Calibration cannot be done without CONSULT).
1.
ALIGN THE VEHICLE STATUS
Stop vehicle with front wheels in straight-ahead position.
>> GO TO 2.
2.
PERFORM CALIBRATION OF DECEL G SENSOR
1. On the CONSULT screen, touch “WORK SUPPORT” and “DECEL G SEN CALIBRATION” in order.
2. Touch “START”.
3. After approximately 10 seconds, touch “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4. Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3.
3.
CHECK DATA MONITOR
1. Run vehicle with front wheels in straight-ahead position, then stop.
2. Select “DATA MONITOR”. Then make sure “DECEL G SEN” is within
± 0.08G.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Perform calibration of decel G sensor again, GO TO 1.
4.
ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
• ABS actuator and electric unit (control unit): Refer to
.
• ECM: Refer to
Situation
Calibration of decel G sensor
Removing/Installing ABS actuator and electric unit (control unit)
—
Replacing ABS actuator and electric unit (control unit)
×
Removing/Installing steering components
—
Replacing steering components
—
Removing/Installing suspension components
—
Replacing suspension components
—
Removing/Installing tire
—
Replacing tire
—
Tire rotation
—
Adjusting wheel alignment
—
Removing/Installing yaw rate/side/decel G sensor
×
Replacing yaw rate/side/decel G sensor
×
BRC-58
< BASIC INSPECTION >
[VDC/TCS/ABS]
CALIBRATION OF DECEL G SENSOR
Are the memories erased?
YES
>> Inspection End.
NO
>> Check the items indicated by the self-diagnosis.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст