Nissan Pathfinder. Manual — part 711
B279B, B279C MODE DOOR MOTOR (REAR)
HAC-105
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
B279B, B279C MODE DOOR MOTOR (REAR)
DTC Logic
INFOID:0000000009176843
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn ignition switch ON.
2. Using CONSULT, perform “SELF-DIAGNOSIS RESULTS” of HVAC.
3. Check if any DTC No. is displayed in the self-diagnosis results.
Is DTC detected?
YES
>> Refer to
HAC-105, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009176844
Regarding Wiring Diagram information, refer to
1.
CHECK MODE DOOR MOTOR (REAR) COMMUNICATION SIGNAL
1. Turn ignition switch ON.
2. Check output waveform between mode door motor (rear) harness connector and ground with the oscillo-
scope.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK INSTALLATION OF MODE DOOR MOTOR (REAR)
Check mode door motor (rear) is properly installed. Refer to
Is the inspection result normal?
DTC
Items
(CONSULT screen terms)
DTC detection condition
Possible cause
B279B
REAR MODE DOOR MOT
When the malfunctioning door position
is detected at VENT position
• Mode door motor (rear)
(PBR internal circuit is open or short-
ed)
• A/C auto amp.
• Harness and connector
(LIN communication line is open or
shorted)
B279C
When the malfunctioning door position
is detected at FOOT position
+
−
Output waveform
Mode door motor (rear)
Connector
Terminal
M13
2
Ground
SJIA1453J
HAC-106
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
B279B, B279C MODE DOOR MOTOR (REAR)
YES
>> Replace mode door motor (rear). Refer to
HAC-164, "MODE DOOR MOTOR : Removal and
Installation - Mode Door Motor (Rear)"
NO
>> Repair or replace malfunctioning part.
3.
CHECK MODE DOOR MOTOR (REAR) COMMUNICATION SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect mode door motor (rear) and A/C auto amp. connector.
3. Check continuity between mode door motor (rear) harness connector and A/C auto amp. harness connec-
tor.
Is the inspection result normal?
YES
>> Replace A/C auto amp. Refer to
HAC-157, "Removal and Installation"
.
NO
>> Repair harness or connector.
Mode door motor (rear)
A/C auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M13
2
M50
16
Yes
B279D, B279E REAR SHUT-OFF DOOR MOTOR
HAC-107
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
B279D, B279E REAR SHUT-OFF DOOR MOTOR
DTC Logic
INFOID:0000000009176845
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn ignition switch ON.
2. Using CONSULT, perform “SELF-DIAGNOSIS RESULTS” of HVAC.
3. Check if any DTC No. is displayed in the self-diagnosis results.
Is DTC detected?
YES
>> Refer to
HAC-107, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009176846
Regarding Wiring Diagram information, refer to
1.
CHECK REAR SHUT-OFF DOOR MOTOR COMMUNICATION SIGNAL
1. Turn ignition switch ON.
2. Check output waveform between rear shut-off door motor harness connector and ground with the oscillo-
scope.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK INSTALLATION OF REAR SHUT-OFF DOOR MOTOR
Check rear shut-off door motor is properly installed. Refer to
.
Is the inspection result normal?
DTC
Items
(CONSULT screen terms)
DTC detection condition
Possible cause
B279D
REAR SHUT DOOR MOT
When the malfunctioning door position
is detected at open position
• Rear shut door motor
(PBR internal circuit is open or short-
ed)
• A/C auto amp.
• Harness and connector
(LIN communication line is open or
shorted)
B279E
When the malfunctioning door position
is detected at closed position
+
−
Output waveform
Mode door motor (rear)
Connector
Terminal
M12
2
Ground
SJIA1453J
HAC-108
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
B279D, B279E REAR SHUT-OFF DOOR MOTOR
YES
>> Replace shut-off door motor. Refer to
HAC-165, "REAR SHUT-OFF DOOR MOTOR : Removal
.
NO
>> Repair or replace malfunctioning part.
3.
CHECK MODE DOOR MOTOR (REAR) COMMUNICATION SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear shut-off door motor and A/C auto amp. connector.
3. Check continuity between rear shut-off door motor harness connector and A/C auto amp. harness con-
nector.
Is the inspection result normal?
YES
>> Replace A/C auto amp. Refer to
HAC-157, "Removal and Installation"
.
NO
>> Repair harness or connector.
Rear shut-off door motor
A/C auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M12
2
M50
16
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст