Nissan Pathfinder. Manual — part 847
ENGINE MAINTENANCE (VQ35DE)
MA-27
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
7. Install engine under cover. Refer to
.
ENGINE OIL : Changing Engine Oil
INFOID:0000000009761158
WARNING:
• Be careful not to burn yourself, as the engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer; try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1. Position the vehicle so it is level on the hoist.
2. Warm up the engine and check for engine oil leaks.
3. Stop engine and wait for 10 minutes.
4. Remove the oil pan drain plug and oil filler cap.
5. Drain the engine oil.
6. Install the oil pan drain plug with a new washer and refill the engine with new engine oil.
CAUTION:
• Be sure to clean the oil pan drain plug and install with a new washer.
• The refill capacity depends on the engine oil temperature and drain time. Use the specifications
for reference only. Always use the dipstick to determine when the proper amount of engine oil is
in the engine.
7. Warm up the engine and check around the oil pan drain plug and oil filter for engine oil leaks.
8. Stop engine and wait for 10 minutes.
9. Check the engine oil level using the dipstick.
CAUTION:
Do not overfill the engine with engine oil.
OIL FILTER
OIL FILTER : Removal and Installation
INFOID:0000000009761159
REMOVAL
1. Drain engine oil. Refer to
MA-27, "ENGINE OIL : Changing Engine Oil"
.
2. Remove front fender protector side cover (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded
.
3. Remove the oil filter using Tool (A) as shown.
WARNING:
Be careful not to burn yourself, as the engine oil may be
hot.
CAUTION:
• When removing, prepare a shop cloth to absorb any
engine oil leaks or spills.
• Do not allow engine oil to adhere to the drive belts.
• Completely wipe off any engine oil that adheres to the
engine and the vehicle.
Engine oil specification and
viscosity
: Refer to
(United States
and Canada) or
(Mexico).
Oil pan drain plug
: 34.3 N·m (3.5 kg-m, 25 ft-lb)
Tool number : KV10115801 (J-38956)
ALBIA0617GB
MA-28
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE (VQ35DE)
• The oil filter is provided with a relief valve. Use a genuine
NISSAN oil filter or equivalent.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply clean engine oil to the oil seal contact surface of the new
oil filter.
3. Screw the oil filter manually until it touches the installation sur-
face, then tighten it by turning another 2/3 turn or tighten to
specification using Tool.
4. Refill the engine with new engine oil. Refer to
MA-27, "ENGINE OIL : Changing Engine Oil"
5. Check the engine oil level and add engine oil as necessary. Refer to
MA-25, "ENGINE OIL : Inspection"
6. After warming up the engine, check for engine oil leaks.
7. Install front fender protector side cover (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
SPARK PLUG
ALC094
SMA010
Oil filter
: 18.0 N·m (1.8 kg-m, 13 ft-lb)
Tool number
: KV10115801 (J-38956)
SMA229B
ENGINE MAINTENANCE (VQ35DE)
MA-29
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
SPARK PLUG : Exploded View
INFOID:0000000009761160
SPARK PLUG : Removal and Installation
INFOID:0000000009761161
REMOVAL
1. Remove the ignition coil. Refer to
EM-42, "Removal and Installation (LH)"
(LH) and
2. Remove the spark plug with a suitable spark plug wrench.
INSPECTION AFTER REMOVAL
1.
Ignition coil
2.
Spark plug
3.
Rocker cover (RH)
4.
Rocker cover (LH)
AWBIA1226GB
PBIC2982E
MA-30
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE (VQ35DE)
Use the standard type spark plug for normal condition.
CAUTION:
• Do not drop or shock spark plug. Discard spark plug if
dropped.
• Do not use a wire brush for cleaning.
• If plug is covered with carbon, a spark plug cleaner may be
used.
• Spark plug gap adjustment is not required between replacement
intervals.
• Measure spark plug gap. When it exceeds the limit, replace spark
plug even if it is within the specified replacement mileage. Refer to
INSTALLATION
Installation is in the reverse order of removal.
*: Always check with the Parts Department for the latest parts information.
EVAP VAPOR LINES
EVAP VAPOR LINES : Inspection
INFOID:0000000009174185
1. Visually inspect EVAP vapor lines for improper attachment and for cracks, damage, loose connections,
chafing and deterioration.
2. Inspect fuel tank filler cap vacuum relief valve for clogging, sticking, etc.
Spark plug
: Refer to
Cleaner air pressure
: less than 588 kPa (6 kg/cm
2
,
85 psi)
Cleaning time
: less than 20 seconds
SMA773C
SMA806CA
Make
DENSO
Standard type*
FXE22HR11
Gap (nominal)
1.1 mm (0.043 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст