Nissan Pathfinder. Manual — part 278
BODY ALIGNMENT
BRM-45
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
Body Center Marks
INFOID:0000000009176389
A mark is placed on each part of the body to indicate the vehicle center. When repairing the vehicle frame
(members, pillars, etc.) damaged in an accident the most accurate and effective repair will be achieved by
using these marks together with body alignment specifications.
Front
Points
Portion
Marks
A
Front roof
Embossment
B
Center cowl top
Hole
C
Front floor
Hole
D
Rear roof
Notch
ALKIA2848ZZ
BRM-46
< SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
Description
INFOID:0000000009176390
• All dimensions indicated in the figures are actual.
• When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself
to make sure there is no free play.
• When a measuring tape is used, check to be sure there is no elongation, twisting or bending.
• Measurements should be taken at the center of the mounting holes.
• An asterisk (*) following the value at the measuring point indicates that the measuring point on the other side
is symmetrically the same value.
• The coordinates of the measurement points are the distances measured from the standard line of
″X″, ″Y″
and
″Z″.
•
″Z″: Imaginary base line [200 mm (7.87 in) below datum line (″0Z″ at design plan)]
Engine Compartment
INFOID:0000000009176391
MEASUREMENT
Dimensions are symmetrically identical on both the RH and LH sides of the vehicle.
1.
Vehicle center
2.
Front axle center
3.
Imaginary base line
JSKIA0073GB
BODY ALIGNMENT
BRM-47
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Unit: mm (in)
Underbody
INFOID:0000000009176392
MEASUREMENT
The following shows a bottom view and a side view of the vehicle.
Position
Description
Measurement
A
Lower radiator support retaining hole 10 (0.4)
980 (38.6)
B
Upper inner bumper reinforcement retaining hole 10 (0.4)
973 (38.3)
C
Upper front radiator support retaining hole to lower radiator support retaining hole 10 (0.4)
1110 (43.7)
D
Upper front radiator support retaining hole 10 (0.4)
970 (38.2)
E
Top radiator support retaining hole 10 (0.4)
970 (38.2)
F
Front fender mounting bracket hole 8 (0.3)
1610 (63.4)
G
Rear hinge retaining hole 10 (0.4) to front fender bracket retaining hole 8 (0.3)
1590 (62.6)
H
Strut tower locator hole 12 (0.5)
1293 (50.9)
J
Center fender bracket retaining hole 8 (0.3)
1645 (64.8)
ALKIA2849ZZ
BRM-48
< SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
Unit: mm (in)
Front
Vehicle left side
Coordinates
Measurement
Coordinates
Measurement
Coordinates
Measurement
A-a
994.10 (39.14)
a-B*
1271.61 (50.00)
a-C*
2005.56 (78.96)
A-d*
2908.27 (114.50)
B-b
654.04 (25.75
B-c*
1119.19 (44.06)
C-c
847.12 (33.35)
C-d*
1351.85 (53.22)
D-d
1027.90 (40.47)
ALKIA2435ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст