Nissan Pathfinder. Manual — part 880
PB-8
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
CAUTION:
Do not reuse the adjusting nut
Adjustment
INFOID:0000000009177221
ADJUSTMENT AFTER INSTALLATION
Adjust the parking brake pedal stroke. Refer to
PARKING BRAKE SHOE
PB-9
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE SHOE
Exploded View
INFOID:0000000009177222
Removal and Installation
INFOID:0000000009177223
REMOVAL
WARNING:
Clean dust on the parking brake shoes with a vacuum dust collector to minimize the hazard of air
borne particles or other materials.
1. Remove the rear wheel and tire using power tool. Refer to
.
2. Remove disc rotor. Refer to
BR-40, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Parking brake must be in the completely released position.
3. If disc rotor cannot be removed, remove as follows:
a. Secure the disc rotor with wheel nuts and remove the adjusting hole plug.
b. Using a suitable tool, rotate adjuster (1) in direction (B) to retract
and loosen parking brake shoe.
4. Remove anti-rattle pins, retainers, anti-rattle springs, adjuster
spring and return spring.
CAUTION:
Do not drop the removed parts.
5. Remove parking brake shoes, adjuster assembly and toggle
lever.
CAUTION:
• The parking brake shoes for the front side are made of dif-
ferent materials from those for the rear side. Do not misi-
dentify them when removing.
• Do not drop the removed parts.
INSTALLATION
Installation is in the reverse order of removal.
1.
Back plate
2.
Parking brake shoe (front)
3.
Adjuster
4.
Adjuster spring
5.
Return spring
6.
Anti-rattle spring
7.
Retainer
8.
Anti-rattle pin
9.
Toggle lever
10. Parking brake shoe (rear)
Front
Apply PBC (Poly Butyl Cuprysil)
grease or silicone based grease
AWFIA0883ZZ
JPFIB0007ZZ
PB-10
< REMOVAL AND INSTALLATION >
PARKING BRAKE SHOE
• Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the back plate and brake shoe.
CAUTION:
The parking brake shoes for the front side are made of different materials from those for the rear
side. Do not misidentify them when removing and replacing.
• Assemble adjusters so that threaded part is expanded when rotat-
ing it in the direction shown by arrow.
• Shorten adjuster by rotating it.
• When assembling the adjuster, apply PBC (Poly Butyl Cuprysil)
grease or silicone-based grease to threads and pivot.
• Check parking brake shoe lining and drum inner surface for
grease. Wipe off any grease on the surfaces.
Inspection and Adjustment
INFOID:0000000009177224
INSPECTION
Brake Lining Thickness Inspection
• Check thickness (A) of brake lining.
Drum Inner Diameter Inspection
• Check inner diameter (B) of drum using suitable tool.
Other Inspections
• Check brake lining for excessive wear, damage, and peeling. Replace if necessary.
• Check parking brake shoe for excessive wear and damage. Replace if necessary.
• Check anti-rattle pins and retainers for excessive wear, damage and rust. Replace if necessary.
• Check adjuster spring, anti-rattle spring and return springs for settling, excessive wear, damage, and rust.
Replace if necessary.
• Check adjuster for binding. Replace if necessary.
• Check toggle lever for excessive wear, damage and rust. Replace if necessary.
• Visually check inside of the drum for rust, cracks, damage or excessive wear with a suitable tool. Replace if
necessary.
ADJUSTMENT
1. Adjust the parking brake pedal stroke. Refer to
PB-4, "Inspection and Adjustment"
(A)
: For RH brake
(B)
: For LH brake
: Front
: Adjuster expands
JPFIB0009ZZ
Limit (A)
: Refer to
.
SBR021A
Limit (B)
: Refer to
.
JPFIB0008ZZ
PARKING BRAKE SHOE
PB-11
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
2. Rotate the disc rotor with the parking brake pedal released and check that there is no drag.
CAUTION:
If any drag is found, verify the parking brake components are installed and adjusted correctly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст