Nissan Pathfinder. Manual — part 998
SB-10
< REMOVAL AND INSTALLATION >
FRONT SEAT BELT
• Tighten the D-ring anchor nut and seat belt retractor bolts to specification.
• Make sure that the seat belt height adjuster is locked in the lowest position and is aligned with the finisher
opening during installation.
• Make sure both the D-ring anchor and seat belt height adjuster operate freely.
• Always perform an inspection after repair to make sure the system is functioning within specifications. Refer
LAP BELT PRETENSIONER
Removal
WARNING:
• Before servicing the SRS, turn the ignition switch off, disconnect both battery terminals then wait at
least three minutes.
• Do not drop the lap belt pretensioner. Always handle it with care.
• Always point pretensioner cylinder away from body when handling.
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove front seat. Refer to
SE-86, "Removal and Installation"
.
3. Release seat belt retractor (1) from the lap belt pretensioner.
a. Insert suitable tool (A) into slots (B).
b. On opposite side insert suitable tool (C) into hole (D).
c.
Depress suitable tools (A) and (C) at the same time and remove
seat belt retractor (1) as shown.
4. Remove the center pillar lower finisher. Refer to
INT-21, "CENTER PILLAR LOWER FINISHER : Removal
5. Position floor trim aside and disconnect the harness connector from the lap belt pretensioner.
CAUTION:
• For removing/installing the shoulder belt pre-tensioner
harness connector, insert a thin screwdriver wrapped in
tape into the notch, then lift the lock and remove the har-
ness connector as shown.
• Install the harness connector with the lock raised, and
push the lock into the harness connector as shown.
• After installing the harness connector, check that the lock
is pushed in securely.
6. Remove floor bracket bolt and floor bracket.
7. Remove lap belt pretensioner bolts and lap belt pretensioner.
ALHIA0321ZZ
PHIA0953J
FRONT SEAT BELT
SB-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
Installation
Installation is in the reverse order of removal.
• Tighten the floor bracket bolt and lap belt pretensioner bolts to specification.
• Always perform an inspection after repair to make sure the system is functioning within specifications. Refer
SEAT BELT HEIGHT ADJUSTER
Removal
1. Slide front seat to the full forward position.
2. Remove the center pillar upper finisher. Refer to
INT-20, "CENTER PILLAR UPPER FINISHER : Removal
3. Remove the D-ring anchor nut.
CAUTION:
Before removing the D-ring anchor nut, note the positions of washers and spacers for correct
installation.
4. Remove the seat belt height adjuster bolts (A) and the seat belt
height adjuster (1).
Installation
Installation is in the reverse order of removal.
• Make sure that the seat belt height adjuster is locked in the lowest position and is aligned with the finisher
opening during installation.
• Tighten the D-ring anchor nut and seat belt height adjuster bolts to specification.
• Make sure both the D-ring anchor and seat belt height adjuster operate freely.
• Always perform an inspection after repair to make sure the system is functioning within specifications. Refer
SEAT BELT BUCKLE
Removal
1. Remove the front seat. Refer to
SE-86, "Removal and Installation"
2. Disconnect the harness connector (if equipped) from seat belt buckle.
3. Remove seat belt buckle anchor bolt and the seat belt buckle.
CAUTION:
Before removing the seat belt buckle anchor bolt, note the positions of washers and spacers for
correct installation.
ALHIA0232GB
SB-12
< REMOVAL AND INSTALLATION >
FRONT SEAT BELT
Installation
Installation is in the reverse order of removal.
• During installation, make sure the seat belt buckle anchor bolt (A)
is inserted through the components in the following order:
• Tighten the seat belt buckle anchor bolt to specification.
• Always perform an inspection after repair to make sure the system is functioning within specifications. Refer
1.
Wave washer
2.
Seat belt buckle
3.
Spacer
4.
Star washer
ALHIA0234GB
SECOND ROW SEAT BELT
SB-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
SECOND ROW SEAT BELT
Second Row Seat Belt
INFOID:0000000009176921
EXPLODED VIEW
SEAT BELT RETRACTOR
Removal - Seat Belt Retractor (LH/RH)
1.
Seat belt height adjuster (LH/RH)
2.
Seat belt retractor (RH)
3.
Lower anchor bolt cover
4.
Seat belt buckle (RH)
5.
Seat belt buckle (center)
6.
Seat belt retractor (LH)
7.
Seat belt retractor (center)
8.
Seat belt retractor finisher
AWHIA0554ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст