Nissan Pathfinder. Manual — part 982
MOONROOF SWITCH
RF-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the harness.
4.
CHECK MOONROOF SWITCH
Check moonroof switch.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace moonroof switch. Refer to
RF-61, "Removal and Installation"
5.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
>> Inspection End.
Component Inspection
INFOID:0000000009176299
MOONROOF SWITCH
1.
CHECK MOONROOF SWITCH
1. Turn ignition switch OFF.
2. Disconnect moonroof switch.
3. Check continuity between moonroof switch terminals.
Is the inspection result normal?
YES
>> Moonroof switch is OK.
NO
>> Replace moonroof switch. Refer to
RF-61, "Removal and Installation"
Moonroof switch
Ground
Continuity
Connector
Terminal
R108
6
Yes
Terminals
Condition
Continuity
3
6
Moonroof switch is operated TILT DOWN or SLIDE OPEN
OPEN
Yes
Other than above
No
10
Moonroof switch is operated TILT UP or SLIDE CLOSE
CLOSE
Yes
Other than above
No
RF-34
< DTC/CIRCUIT DIAGNOSIS >
SUNSHADE SWITCH
SUNSHADE SWITCH
Description
INFOID:0000000009176300
Transmits switch operation signal to sunshade motor assembly.
Diagnosis Procedure
INFOID:0000000009176301
Regarding Wiring Diagram information, refer to
1.
CHECK SUNSHADE SWITCH INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between sunshade motor assembly harness connector and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> GO TO 2.
2.
CHECK SUNSHADE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect sunshade motor assembly connector and sunshade switch connector.
3. Check continuity between sunshade motor assembly harness connector and sunshade switch harness
connector.
4. Check continuity between sunshade motor assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or the replace harness.
3.
CHECK SUNSHADE SWITCH GROUND CIRCUIT
Check continuity between sunshade switch harness connector and ground.
(+)
(–)
Condition
Voltage
(Approx.)
Sunshade motor assembly
Connector
Terminals
B85
6
Ground
Sunshade switch is operated
OPEN (1st)
0
Other than above
Battery voltage
2
Sunshade switch is operated
CLOSE (2nd)
0
Other than above
Battery voltage
Sunshade motor assembly
Sunshade switch
Continuity
Connector
Terminal
Connector
Terminal
B85
2
R110
3
Yes
6
1
Sunshade motor assembly
Ground
Continuity
Connector
Terminal
B85
2
No
6
SUNSHADE SWITCH
RF-35
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the harness.
4.
CHECK SUNSHADE SWITCH
Check sunshade switch.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace sunshade switch. Refer to
RF-62, "Removal and Installation"
.
5.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
>> Inspection End.
Component Inspection
INFOID:0000000009176302
SUNSHADE SWITCH
1.
CHECK SUNSHADE SWITCH
1. Turn ignition switch OFF.
2. Disconnect sunshade switch.
3. Check continuity between sunshade switch terminals.
Is the inspection result normal?
YES
>> Sunshade switch is OK.
NO
>> Replace sunshade switch. Refer to
RF-62, "Removal and Installation"
.
Sunshade switch
Ground
Continuity
Connector
Terminal
R110
2
Yes
Terminals
Condition
Continuity
1
2
Sunshade switch is operated
OPEN
Yes
Other than above
No
3
Sunshade switch is operated
CLOSE
Yes
Other than above
No
RF-36
< DTC/CIRCUIT DIAGNOSIS >
DOOR SWITCH
DOOR SWITCH
Component Function Check
INFOID:0000000009764008
1.
CHECK FUNCTION
1. Select DOOR LOCK of BCM using CONSULT.
2. Select DOOR SW-DR, DOOR SW-AS, DOOR SW-RL, DOOR SW-RR, in DATA MONITOR mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door switch is OK.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000009764009
Regarding Wiring Diagram information, refer to
.
1.
CHECK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect malfunctioning door switch connector.
3. Check signal between malfunctioning door switch harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between door switch harness connector and BCM harness connector.
Monitor item
Condition
Status
DOOR SW-DR
Driver side door
Open
On
Closed
Off
DOOR SW-AS
Passenger side door
Open
On
Closed
Off
DOOR SW-RL
Rear door LH
Open
On
Closed
Off
DOOR SW-RR
Rear door RH
Open
On
Closed
Off
(+)
(–)
Signal
(Reference value)
Door switch
Connector
Terminal
Driver side
B8
3
Ground
7.0 - 8.0 V
Passenger side
B108
Rear LH
B18
Rear RH
B116
PKIB4960J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст