Nissan Pathfinder. Manual — part 356
DLK-190
< DTC/CIRCUIT DIAGNOSIS >
UNLOCK SENSOR
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK UNLOCK SENSOR
DLK-190, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly LH. Refer to
DLK-301, "DOOR LOCK : Removal and Installa-
.
5.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
>> Inspection End.
Component Inspection
INFOID:0000000009175737
1.
CHECK UNLOCK SENSOR
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly LH connector.
3. Check continuity between front door lock assembly LH terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace front door lock assembly LH. Refer to
DLK-301, "DOOR LOCK : Removal and Installa-
.
Front door lock assembly LH
Ground
Continuity
Connector
Terminal
D14
4
Yes
Front door lock assembly LH
Condition
Continuity
Terminal
3
4
Driver side door
Unlock
Yes
Lock
No
DOOR KEY CYLINDER SWITCH
DLK-191
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR KEY CYLINDER SWITCH
Component Function Check
INFOID:0000000009175738
1.
CHECK FUNCTION
1. Select DOOR LOCK of BCM using CONSULT.
2. Select KEY CYL LK-SW, KEY CYL UN-SW in DATA MONITOR mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door key cylinder switch is OK.
NO
>> Refer to
DLK-191, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009175739
Regarding Wiring Diagram information, refer to
.
1.
CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly LH connector.
3. Check voltage between front door lock assembly LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR KEY CYLINDER SWITCH SIGNAL CIRCUIT
1. Disconnect power window main switch connector.
2. Check continuity between main power window and door lock/unlock switch harness connector and front
door lock assembly LH harness connector.
3. Check continuity between power window main switch harness connector and ground.
Monitor item
Condition
Status
KEY CYL LK-SW
Driver side door key cylinder
Lock
ON
Neutral / Unlock
OFF
KEY CYL UN-SW
Unlock
ON
Neutral / Lock
OFF
(+)
(–)
Voltage
(Approx.)
Front door lock assembly LH
Connector
Terminal
D14
5
Ground
5 V
6
Main power window and door lock/unlock switch
Front door lock assembly LH
Continuity
Connector
Terminal
Connector
Terminal
D25
3
D14
6
Yes
15
5
DLK-192
< DTC/CIRCUIT DIAGNOSIS >
DOOR KEY CYLINDER SWITCH
Is the inspection result normal?
YES
>> Replace main power window and door lock/unlock switch. Refer to
.
NO
>> Repair or replace harness.
3.
CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT
Check continuity between front door lock assembly LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR KEY CYLINDER SWITCH
DLK-192, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly LH. Refer to
DLK-301, "DOOR LOCK : Removal and Installa-
.
5.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
>> Inspection End.
Component Inspection
INFOID:0000000009175740
1.
CHECK DOOR KEY CYLINDER SWITCH
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly LH connector.
3. Check continuity between front door lock assembly LH terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace front door lock assembly LH. Refer to
DLK-301, "DOOR LOCK : Removal and Installa-
.
Main power window and door lock/unlock switch
Ground
Continuity
Connector
Terminal
D25
3
No
15
Front door lock assembly LH
Ground
Continuity
Connector
Terminal
D14
4
Yes
Front door lock assembly LH
Condition
Continuity
Terminal
5
4
Driver side door key cylinder
Unlock
Yes
Neutral / Lock
No
6
Lock
Yes
Neutral / Unlock
No
REMOTE KEYLESS ENTRY RECEIVER
DLK-193
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY RECEIVER
Component Function Check
INFOID:0000000009175741
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “RKE OPE COUN1” in “DATA MONITOR” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Remote keyless entry receiver is OK.
NO
>> Refer to
DLK-193, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009175742
Regarding Wiring Diagram information, refer to
.
1.
CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 1
1. Disconnect BCM and remote keyless entry receiver connectors.
2. Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
Monitor item
Condition
RKE OPE COUN1
Checks whether value changes when operating Intelligent Key
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M80
119
Ground
Standby state
Press the Intelligent
Key lock or unlock
button
OCC3881D
OCC3880D
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M80
119
M86
2
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст