Nissan Pathfinder. Manual — part 741
INTERIOR ROOM LAMP CONTROL CIRCUIT
INL-51
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
INTERIOR ROOM LAMP CONTROL CIRCUIT
Description
INFOID:0000000009175443
Controls the room lamp control circuit (ground side) to turn the room lamps ON and OFF.
Component Function Check
INFOID:0000000009175444
CAUTION:
Before performing the diagnosis, check that the following are normal.
• Battery saver output/power supply
• Front room/map lamp bulb
• Personal lamp 2nd row bulb
• Cargo lamp bulb
1.
CHECK INTERIOR ROOM LAMP CONTROL FUNCTION
CONSULT
1. Set the front room/map lamp switch, personal lamp switch and cargo lamp switch to DOOR.
2. Turn ignition switch ON.
3. Select INT LAMP of BCM(INT LAMP) active test item.
4. While operating the test item, check that each interior room lamp turn ON/OFF.
Does the interior room lamp turn ON/OFF?
YES
>> Interior room lamp control circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009175445
Regarding Wiring Diagram information, refer to
.
1.
CHECK INTERIOR ROOM LAMP CONTROL OUTPUT
CONSULT
1. Turn ignition switch ON.
2. Select INT LAMP of BCM(INT LAMP) active test item.
3. While operating the test item, check voltage between BCM harness connector M81 terminal 136 and
ground.
Is the inspection result normal?
YES
>> Interior room lamp control circuit is operating normally.
Fixed ON>>GO TO 3.
Fixed OFF>>GO TO 2.
2.
CHECK INTERIOR ROOM LAMP CONTROL OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector M81, front room/map lamp harness connector R107 and cargo lamp
harness connector R104.
3. Check continuity between BCM harness connector M81 terminal 136 and front room/map lamp assembly
harness connector R107 terminal 3 and cargo lamp harness connector R104 terminal 3.
On
: Interior room lamp On
Off
: Interior room lamp Off
BCM
Ground
Test item
Voltage
(Approx.)
Connector
Terminal
M81
136
INT LAMP
On
0V
Off
Battery voltage
INL-52
< DTC/CIRCUIT DIAGNOSIS >
INTERIOR ROOM LAMP CONTROL CIRCUIT
4. Reconnect the front room/map lamp assembly harness connector.
5. Check continuity between BCM harness connector M81 terminal 136 and personal lamps 2nd row har-
ness connector R106 terminal 3.
Is the inspection result normal?
YES
>> Check interior room lamps for an open. If NG, replace lamp in question. Refer to
(front room/map lamp assembly) or
INL-65, "Removal and Installation"
(personal lamps 2nd row) or
INL-66, "Removal and Installation"
(cargo lamp). If OK, replace BCM.
BCS-80, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
3.
CHECK INTERIOR ROOM LAMP CONTROL SHORT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector M81, front room/map lamp harness connector R107 and cargo lamp
harness connector R104.
3. Check continuity between BCM harness connector M81 terminal 136 and ground.
Is the inspection result normal?
YES
>> Check interior room lamps for an open. If NG, replace lamp in question. Refer to
(front room/map lamp assembly) or
INL-65, "Removal and Installation"
(personal lamps 2nd row) or
INL-66, "Removal and Installation"
(cargo lamp). If OK, replace BCM.
BCS-80, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
BCM
Interior room lamp
Continuity
Connector
Terminal
Connector
Terminal
M81
136
Front room/map lamp
R107
3
Yes
Cargo lamp
R104
3
BCM
Personal lamp
Continuity
Connector
Terminal
Connector
Terminal
M81
136
R106
3
Yes
BCM
Ground
Continuity
Connector
Terminal
M81
136
No
STEP LAMP CIRCUIT
INL-53
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
STEP LAMP CIRCUIT
Description
INFOID:0000000009175446
Controls the step lamp control circuit (ground side) to turn the step lamps (if equipped) and foot lamps (if
equipped) ON and OFF.
Component Function Check
INFOID:0000000009175447
CAUTION:
Before performing the diagnosis, check that the following is normal.
• Battery saver output/power supply
• Front step lamp bulb (if equipped)
• Foot lamp bulb (if equipped)
1.
CHECK STEP LAMP OPERATION
CONSULT
1. Turn ignition switch ON.
2. Select STEP LAMP TEST of BCM(INT LAMP) active test item.
3. While operating the test items, check that front step lamp (if equipped) and foot lamp (if equipped) turns
ON/OFF.
Is the inspection result normal?
YES
>> Step lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009175448
Regarding Wiring Diagram information, refer to
.
1.
CHECK STEP LAMP OUTPUT
CONSULT
1. Turn ignition switch ON.
2. Select STEP LAMP TEST of BCM (INT LAMP) active test item.
3. While operating the test item, check voltage between BCM harness connector M18 terminal 21 and
ground.
Is the inspection result normal?
YES
>> Step lamp control circuit is operating normally.
Fixed ON>>GO TO 3.
Fixed OFF>>GO TO 2.
2.
CHECK STEP LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect the following harness connectors:
-
BCM M18
-
Front step lamp LH D11(if equipped)
-
Front step lamp RH D109 (if equipped)
-
Foot lamp LH M99 (if equipped)
-
Foot lamp RH M100 (if equipped)
On
: Step lamp and foot lamp ON
Off
: Step lamp and foot lamp OFF
BCM
Ground
STEP LAMP TEST
Voltage
(Approx.)
Connector
Terminal
M18
21
On
0V
Off
Battery voltage
INL-54
< DTC/CIRCUIT DIAGNOSIS >
STEP LAMP CIRCUIT
3. Check continuity between BCM harness connector M18 terminal 21 and the following lamp harness con-
nector terminal.
Is the inspection result normal?
YES
>> Check front step lamp (if equipped) or foot lamp (if equipped) for an open. If NG, replace lamp in
question. Refer to
INL-64, "Removal and Installation"
"DRIVER SIDE : Removal and Installation"
(foot lamp) (if equipped). If OK, replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Repair or replace harness or connector.
3.
CHECK STEP LAMP SHORT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect the following harness connectors:
-
BCM M18
-
Front step lamp LH D11(if equipped)
-
Front step lamp RH D109 (if equipped)
-
Foot lamp LH M99 (if equipped)
-
Foot lamp RH M100 (if equipped)
3. Check continuity between BCM harness connector M18 terminal 21 and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Repair or replace harness or connector.
BCM
Step lamp
Continuity
Connector
Terminal
Connector
Terminal
M18
21
Front step lamp LH (if equipped)
D11
2
Yes
Front step lamp RH (if equipped)
D109
Foot lamp LH (if equipped)
M99
Foot lamp RH (if equipped)
M100
BCM
Ground
Continuity
Connector
Terminal
M18
21
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст