Nissan Pathfinder. Manual — part 1070
PANIC ALARM FUNCTION DOES NOT OPERATE
SEC-143
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
PANIC ALARM FUNCTION DOES NOT OPERATE
Description
INFOID:0000000009176073
NOTE:
• Before performing the diagnosis following procedure, check “Work Flow”. Refer to
.
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis and
check each symptom.
CONDITIONS OF VEHICLE (OPERATION CONDITIONS)
• Ignition switch is in OFF or LOCK position.
• Intelligent Key is removed from key slot.
Diagnosis Procedure
INFOID:0000000009176074
1.
CHECK REMOTE KEYLESS ENTRY FUNCTION
Check remote keyless entry function.
Does door lock/unlock with Intelligent Key button?
YES
>> GO TO 2.
NO
>> Go to
DLK-238, "Diagnosis Procedure"
2.
CHECK VEHICLE SECURITY ALARM OPERATION
Check vehicle security alarm operation.
Does alarm (headlamps and horns) active?
YES
>> GO TO 3.
NO
>> Go to
SEC-14, "VEHICLE SECURITY SYSTEM : System Description"
.
3.
CHECK “PANIC ALARM SET” SETTING IN “WORK SUPPORT”
Check “PANIC ALARM SET” setting in “WORK SUPPORT”.
BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “PANIC ALARM SET” setting in “WORK SUPPORT”.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-49, "Intermittent Incident"
.
NO
>> GO TO 1.
SEC-144
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
NATS ANTENNA AMP.
REMOVAL AND INSTALLATION
NATS ANTENNA AMP.
Exploded View
INFOID:0000000009176075
Removal and Installation
INFOID:0000000009176076
REMOVAL
1. Remove the instrument lower panel LH. Refer to
IP-25, "Removal and Installation"
.
2. Disconnect the harness connector from the NATS antenna amp and the push button ignition switch.
3. Release the pawl on each side of NATS antenna amp and remove from the instrument pad (LH).
4. Release the pawl on each side and remove the NATS antenna amp from the push-button ignition switch.
INSTALLATION
Installation is in the reverse order of removal.
1.
NATS antenna amp.
2.
Push-button ignition switch
ALKIA2470ZZ
PUSH-BUTTON IGNITION SWITCH
SEC-145
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
PUSH-BUTTON IGNITION SWITCH
Exploded View
INFOID:0000000009176077
Removal and Installation
INFOID:0000000009176078
REMOVAL
1. Remove the instrument lower panel LH. Refer to
IP-25, "Removal and Installation"
.
2. Disconnect the harness connector from the NATS antenna amp and the push button ignition switch.
3. Release the pawl on each side of NATS antenna amp and remove from the instrument pad (LH).
4. Release the pawl on each side and remove the NATS antenna amp from the push-button ignition switch.
INSTALLATION
Installation is in the reverse order of removal.
1.
NATS antenna amp.
2.
Push-button ignition switch
ALKIA2470ZZ
SEC-146
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
IMMOBILIZER CONTROL MODULE
IMMOBILIZER CONTROL MODULE
Removal and Installation
INFOID:0000000009176079
The immobilizer control module is integrated into the body control module (BCM). For removal and installation,
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст