Nissan Pathfinder. Manual — part 1031
SE-122
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
cushion trim and seat cushion pad wires.
• Use NISSAN standard hog rings and tools to assemble.
• Make sure hook fastener is pressed into place after seat cushion
trim is assembled.
• Smooth out all wrinkles during assembly.
CAUTION:
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After work is completed, check that no system malfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warning lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to
.
PIIB3356J
SECOND ROW SEAT
SE-123
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
SECOND ROW SEAT
Exploded View
INFOID:0000000009727792
LH SEAT
AWJIA1000ZZ
1.
Headrest (RH)
2.
Headrest holder (free) (RH)
3.
Headrest holder (locked) (RH)
4.
Cup holder
5.
Armrest hinge finisher
6.
Armrest assembly
SE-124
< UNIT DISASSEMBLY AND ASSEMBLY >
SECOND ROW SEAT
7.
Seat cushion trim
8.
Seat cushion pad
9.
Seat cushion frame
10
Seat cushion latch finisher
11. Outer finisher (RH)
12. Inner finisher (RH)
13. Recline finisher (center)
14. Seat belt buckle (RH)
15. Seat belt retractor (center)
16. Seat slide clip (RH)
17. Seat slide release cable
18. Seat cushion release cable
19. Seat slide control lever assembly
20. Front slide finisher (RH)
21. Seat slide clip (LH)
22. Rear slide finisher (RH)
23. Front slide finisher (LH)
24. Rear slide finisher (LH)
25. Support strut
26. Recline release cable assembly
27. Seat frame assembly
28. Seat harness
29. Recline lever
30. Seat cushion outer finisher LH
31. Rear finisher
32. EZ entry cable
33. Dampener
34. Trim stiffener (RH)
35. Trim stiffener (LH)
36. Tether anchor finisher
37. Seatback board
38. EPP upper panel
39. Seat belt retractor finisher
40. Support finisher (RH)
41. EZ entry lever finisher
42. EZ entry finisher
43. Seatback pad
44. Seatback trim
45. Headrest holder (locked) (LH)
46. Headrest (LH)
47. Headrest holder (free) (LH)
48. Seat belt retractor finisher
A.
Seat cushion pivot bolt
SECOND ROW SEAT
SE-125
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
RH SEAT
AWJIA0985ZZ
1.
EZ entry finisher
2.
EZ entry lever finisher
3.
Seat cushion trim
4.
Seat cushion pad
5.
Recline lever
6.
Seat cushion outer finisher (RH)
7.
Seat cushion frame
8.
Recline release cable assembly
9.
Dampener
10. Seat cushion latch finisher
11. Track tilt release cable
12. Seat slide control lever assembly
13. Rear slide finisher (RH)
14. Front slide finisher (RH)
15. Front slide finisher (LH)
16. Rear slide finisher (LH)
17. Seat frame assembly
18. Seat slide clip
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст