Nissan Pathfinder. Manual — part 973
RAX-14
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR DRIVE SHAFT
8. Install new large and small boot bands securely to specification
and using Tool.
CAUTION:
Do not reuse boot bands.
• Secure boot band so that dimension (M) meets specification
as shown.
9. After installing joint sub-assembly and shaft, make sure that they are in the correct position when rotating
boot. If boot position is not correct, remove old boot bands then reposition the boot and secure with new
boot bands.
CAUTION:
Do not reuse boot bands.
Final Drive Side
1. Install new boot and new small boot band to shaft.
CAUTION:
• Cover drive shaft serration with tape to prevent damage to boot during installation.
• Do not reuse boot or boot band.
2. Remove protective tape wrapped around serrated part of shaft.
3. Install the spider assembly (1).
• Align it with the matching marks (A) on the shaft (2) made dur-
ing disassembly and direct the serration mounting surface (B)
onto the shaft.
Tool number
: KV40107300 ( — )
RAC1133D
Dimension (M)
: Refer to
.
DSF0047D
SFA800
JPDIF0017ZZ
REAR DRIVE SHAFT
RAX-15
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
4. Install new snap ring (1) using suitable tool onto shaft.
CAUTION:
Do not reuse snap ring.
5. Pack housing with the specified amount of new grease (Genuine NISSAN Grease or equivalent).
6. Align matching marks made during disassembly and install the housing onto spider assembly.
7. After installation, pull shaft to check engagement between slide joint assembly and circular clip.
8. Install boot securely into grooves (indicated by “*” marks) as
shown.
CAUTION:
If there is grease on boot mounting surfaces (indicated by
“*” marks) on shaft or housing, boot may come off. Clean
all grease from the boot mounting surfaces (*).
9. Make sure boot installation length (L) is the length specified
below. Insert a suitable tool into large end of boot. Bleed air from
boot to prevent boot deformation.
CAUTION:
• Boot may break if boot installation length exceeds or is less then the standard value.
• Be careful that suitable tool does not contact inside surface of the boot.
10. Install new large and small boot bands securely using Tool.
CAUTION:
Do not reuse boot band.
• Secure boot band so the dimension (M) meets specifications
as shown.
JPDIF0014ZZ
Grease amount
: Refer to
.
Boot installation
length (L)
: Refer to
.
Tool number
: KV40107300 ( — )
JPDIF0224ZZ
RAC1133D
Dimension (M)
: Refer to
.
DSF0047D
RAX-16
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR DRIVE SHAFT
11. After installing housing and shaft, rotate boot to validate position is correct. If boot position is incorrect,
remove boot bands and reposition the boot, then secure with new boot bands.
CAUTION:
Do not reuse boot band.
12. Install a new dust shield.
13. Install a new circular clip.
CAUTION:
Do not reuse circular clip.
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-17
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000009177870
Drive Shaft
INFOID:0000000009177871
* : Boot installation grooves
Boot Bands
Unit: mm (in)
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
Application
Standard
Joint type
Wheel side
Final drive side
Grease quantity
55
± 10 g
(1.94
± 0.35 oz)
60
± 10 g
(2.12
± 0.35 oz)
Boots installed length
113.5 mm (4.47 in)
118.2 mm (4.65 in)
JPDIF0142ZZ
JPDIF0144ZZ
Dimension (M)
1.0 - 4.0 (0.039 - 0.157)
DSF0047D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст