Nissan Pathfinder. Manual — part 39
ADP-148
< DTC/CIRCUIT DIAGNOSIS >
TILT MOTOR
TILT MOTOR
Description
INFOID:0000000009176656
• The tilt motor is installed to the steering column assembly.
• The tilt motor is activated with the automatic drive positioner control unit.
• The steering column is tilted upward/downward by changing the rotation direction of tilt motor.
Component Function Check
INFOID:0000000009176657
1.
CHECK FUNCTION
1. Select “TILT MOTOR” in “ACTIVE TEST” mode with CONSULT.
2. Check the tilt motor operation.
Is the operation of relevant parts normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
ADP-148, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009176658
Regarding Wiring Diagram information, refer to
ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"
or
ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"
.
1.
CHECK TILT MOTOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect tilt motor.
3. Turn the ignition switch ON.
4. Perform “ACTIVE TEST” (“TILT MOTOR”) with CONSULT.
5. Check voltage between tilt motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace tilt motor. Refer to
NO
>> GO TO 2.
2.
CHECK TILT MOTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit.
3. Check continuity between automatic drive positioner control unit harness connector and tilt motor harness
connector.
Test item
Description
TILT MOTOR
OFF
Steering tilt
Stop
UP
Upward
DWN
Downward
(+)
(–)
Condition
Voltage (V)
(Approx.)
Tilt motor
Connector
Terminals
M85
2
Ground
TILT
MOTOR
OFF
0
UP
0
DWN (down)
Battery voltage
1
OFF
0
UP
Battery voltage
DWN (down)
0
TILT MOTOR
ADP-149
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-162, "Removal and Installation"
.
NO
>> Repair or replace harness.
Automatic drive positioner con-
trol unit
Tilt motor
Continuity
Connector
Terminal
Connector
Terminal
M34
28
M85
2
Yes
29
1
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M34
28
No
29
ADP-150
< DTC/CIRCUIT DIAGNOSIS >
TELESCOPIC MOTOR
TELESCOPIC MOTOR
Description
INFOID:0000000009176659
• The telescopic motor is installed to the steering column assembly.
• The telescopic motor is activated with the automatic drive positioner control unit.
• Compresses the steering column by changing the rotation direction of telescopic motor.
Component Function Check
INFOID:0000000009176660
1.
CHECK FUNCTION
1. Select “TELESCO MOTOR” in “ACTIVE TEST” mode with CONSULT.
2. Check the telescopic motor operation.
Is the operation of relevant parts normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
ADP-150, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009176661
Regarding Wiring Diagram information, refer to
ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"
or
ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"
.
1.
CHECK TELESCOPIC MOTOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect telescopic motor.
3. Turn the ignition switch ON.
4. Perform “ACTIVE TEST” (“TELESCO MOTOR”) with CONSULT.
5. Check voltage between telescopic motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace telescopic motor. Refer to
NO
>> GO TO 2.
2.
CHECK TELESCOPIC MOTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit.
3. Check continuity between automatic drive positioner control unit harness connector and telescopic motor
harness connector.
Test item
Description
TELESCO MOTOR
OFF
Steering telescopic
Stop
FR Forward
RR
Backward
(+)
(–)
Condition
Voltage (V)
(Approx.)
Telescopic motor
Connector
Terminals
M94
2
Ground
TELE-
SCOPIC
MOTOR
OFF
0
FR (forward)
0
RR (backward)
Battery voltage
1
OFF
0
FR (forward)
Battery voltage
RR (backward)
0
TELESCOPIC MOTOR
ADP-151
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-162, "Removal and Installation"
.
NO
>> Repair or replace harness.
Automatic drive positioner control
unit
Telescopic motor
Continuity
Connector
Terminal
Connector
Terminal
M34
29
M94
1
Yes
26
2
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M34
29
No
26
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст