Nissan Pathfinder. Manual — part 407
DLN-70
< PERIODIC MAINTENANCE >
[TRANSFER: TY21C]
TRANSFER OIL
PERIODIC MAINTENANCE
TRANSFER OIL
Inspection
INFOID:0000000009177767
TRANSFER OIL LEAKS
Check that oil is not leaking from transfer assembly or around it.
TRANSFER OIL LEVEL
CAUTION:
Do not start engine while checking transfer oil level.
1. Remove filler plug (1) and gasket.
2. Transfer oil level (A) should be level with bottom of filler plug
hole. Add transfer oil if necessary. Refer to
AND CANADA : Fluids and Lubricants"
(United States and Can-
MA-16, "FOR MEXICO : Fluids and Lubricants"
ico).
3. Set a new gasket onto filler plug, and install it in the transfer and
tighten to specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
Draining
INFOID:0000000009177768
CAUTION:
Do not start engine while working.
1. Run the vehicle to warm up the transfer unit sufficiently.
2. Stop the engine and remove drain plug (1) and gasket and drain
the transfer oil.
3. Set a new gasket onto filler plug, and install it in the transfer and
tighten to specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
Refilling
INFOID:0000000009177769
CAUTION:
Do not start engine while checking transfer oil level.
1. Remove filler plug (1).
2. Fill with new transfer oil to the specified level near the filler plug
hole.
: Front
ALDIA0383ZZ
: Front
ALDIA0382ZZ
: Front
ALDIA0383ZZ
TRANSFER OIL
DLN-71
< PERIODIC MAINTENANCE >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3. Set a new gasket onto filler plug, and install it in the transfer and tighten to specified torque. Refer to
CAUTION:
Do not reuse gasket.
Transfer oil grade and
viscosity
: Refer to
AND CANADA : Fluids and
Lubricants"
(United States
and Canada) or
MEXICO : Fluids and Lubri-
cants"
Transfer oil capacity
: Refer to
DLN-72
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
4WD CONTROL UNIT
REMOVAL AND INSTALLATION
4WD CONTROL UNIT
Removal and Installation
INFOID:0000000009177770
REMOVAL
1. Disconnect the negative battery terminal. Refer to
2. Remove storage box. Refer to
.
3. Remove 4WD control unit bolts (
).
4. Disconnect 4WD control unit harness connector.
5. Remove 4WD control unit (1).
INSTALLATION
Installation is in the reverse order of removal.
• Tighten 4WD control unit bolts to specified torque.
CAUTION:
Do not drop or shock 4WD control unit.
Reset electronic systems as necessary. Refer to
PG-89, "ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL : Special Repair Requirement"
.
: Front
ALDIA0278ZZ
4WD control unit bolts
: 10.1 N·m (1.0 kg-m, 7 ft-lb)
4WD SHIFT SWITCH
DLN-73
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4WD SHIFT SWITCH
Removal and Installation
INFOID:0000000009177771
REMOVAL
1. Remove the CVT shift selector finisher. Refer to
2. Remove the 4WD lock switch finisher (1).
3. Remove the front seat climate control switch bracket screws (1)
and the CVT shift selector indicator lamp screws (2). Refer to
4. Separate the CVT shift selector indicator lamp from the CVT
shift selector finisher by pressing down on the pawls.
: Pawls
5. Remove the 4WD lock switch from the CVT shift selector indicator lamp.
INSTALLATION
Installation is in the reverse order of removal.
ALDIA0387ZZ
ALDIA0384ZZ
ALDIA0386ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст