Nissan Pathfinder. Manual — part 1178
OVERDRIVE CONTROL SWITCH
TM-171
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK CIRCUIT BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER (PART 1)
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between CVT shift selector harness connector terminal and combination meter harness
connector terminal.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning parts.
6.
CHECK CIRCUIT BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER (PART 2)
Check continuity between CVT shift selector harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace malfunctioning parts.
7.
CHECK COMBINATION METER INPUT SIGNAL
1. Connect all of disconnected connectors.
2. Turn ignition switch ON.
3. Select “Data Monitor” in “METER/M&A”.
4. Select “O/D OFF SW”.
5. Check that “O/D OFF SW” turns ON/OFF when overdrive control switch is operated. Refer to
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-49, "Intermittent Incident"
.
NO
>> Replace combination meter. Refer to
MWI-82, "Removal and Installation"
Component Inspection
INFOID:0000000009177627
1.
CHECK OVERDRIVE CONTROL SWITCH
CVT shift selector
—
Continuity
Connector
Terminal
M78
2
Ground
Existed
CVT shift selector
Combination meter
Continuity
Connector
Terminal
Connector
Terminal
M78
1
M24
52
Existed
CVT shift selector
—
Continuity
Connector
Terminal
M78
1
Ground
Not existed
TM-172
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
OVERDRIVE CONTROL SWITCH
Check continuity between wires of shift selector handle .
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace shift selector handle. Refer to
.
Condition
Continuity
Overdrive control switch is de-
pressed
Existed
Overdrive control switch is released
Not existed
JSDIA2795ZZ
OD OFF INDICATOR LAMP
TM-173
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OD OFF INDICATOR LAMP
Component Function Check
INFOID:0000000009177628
1.
CHECK OD OFF INDICATOR LAMP FUNCTION
Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection results normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009177629
1.
CHECK DTC (TCM)
With CONSULT
1. Turn ignition switch ON.
2. Check “Self Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
.
NO
>> GO TO 2.
2.
CHECK DTC (COMBINATION METER)
With CONSULT
Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
NO
>> GO TO 3.
3.
CHECK COMBINATION METER INPUT/OUTPUT SIGNAL
With CONSULT
1. Shift the selector lever to “D” position.
2. Select “Data Monitor” in “METER/M&A”.
3. Select “O/D OFF IND”.
4. Check that “O/D OFF IND” turns ON/OFF when overdrive control switch is operated. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-82, "Removal and Installation"
NO
>> GO TO 4.
4.
CHECK TCM INPUT/OUTPUT SIGNAL
With CONSULT
1. Select “Data Monitor” in “TCM”.
2. Select “SPORT MODE IND”.
3. Check that “SPORT MODE IND” turns ON/OFF when overdrive control switch is operated. Refer to
.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-82, "Removal and Installation"
NO
>> Check overdrive control switch circuit. Refer to
.
TM-174
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
TOW MODE SYSTEM
TOW MODE SYSTEM
Component Function Check
INFOID:0000000009177630
1.
CHECK TOW MODE SWITCH FUNCTION
Check that TOW mode indicator lamp turns ON/OFF when tow mode switch is operated.
Is the inspection results normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009177631
1.
CHECK DTC (TCM)
With CONSULT
1. Start the engine.
2. Check “Self Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
.
NO
>> GO TO 2.
2.
CHECK DTC (COMBINATION METER)
With CONSULT
Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
NO
>> GO TO 3.
3.
CHECK COMBINATION METER INPUT/OUTPUT SIGNAL
With CONSULT
1. Select “Data Monitor” in “METER/M&A”.
2. Select “TOW MODE IND”.
3. Check that “TOW MODE IND” turns ON/OFF when tow mode switch is operated. Refer to
Is the inspection result normal?
YES
>> Replace the combination meter. Refer to
MWI-82, "Removal and Installation"
.
NO
>> GO TO 4.
4.
CHECK TOW MODE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect tow mode switch connector.
3. Turn ignition switch ON.
4. Check voltage between tow mode switch harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 6.
5.
CHECK TOW MODE SWITCH
Check tow mode switch. Refer to
TM-175, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-49, "Intermittent Incident"
.
Tow mode switch
Voltage
(Approx.)
Connector
+
−
Terminal
M6
1
4
Battery voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст