Nissan Pathfinder. Manual — part 145
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-407
< SYSTEM DESCRIPTION >
[PREMIUM AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Display Diagnosis
Vehicle Signals
A comparison check can be made of each actual vehicle signal and
the signals recognized by the system.
Speaker Test
AWNIA2603GB
JSNIA2991ZZ
AV-408
< SYSTEM DESCRIPTION >
[PREMIUM AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Select Speaker Test to display the Speaker Diagnosis screen. Press
Start to generate a test tone in a speaker. Press Start again to gener-
ate a test tone in the next speaker. Press End to stop the test tones.
Navigation
STEERING ANGLE ADJUSTMENT
The steering angle output value detected with the gyroscope is
adjusted.
SPEED CALIBRATION
During normal driving, distance error caused by tire wear and tire
pressure change is automatically adjusted for by the automatic dis-
tance correction function. This function, on the other hand, is for
immediate adjustment, in cases such as driving with tire chain fitted
on tires.
Error History
The self-diagnosis results are judged depending on whether any error occurs from when “Self-diagnosis” is
selected until the self-diagnosis results are displayed.
However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned
ON and then no error has occurred until the self-diagnosis start. Check the “Error Record” to detect any error
that may have occurred before the self-diagnosis start because of this situation.
The error record displays the time and place of the most recent occurrence of that error. However, take note of
the following points.
• If there is a malfunction with the GPS antenna circuit board in the AV control unit, the correct date and time
of occurrence may not be able to be displayed.
• Place of the error occurrence is represented by the position of the current location mark at the time an error
occurred. If current location mark has deviated from the correct position, then the place of the error occur-
rence cannot be located correctly.
• The frequency of occurrence is displayed in a count up manner. The actual count up method differs depend-
ing on the error item.
Count up method A
• The counter resets to 0 if an error occurs when ignition switch is turned ON. The counter increases by 1 if
the condition is normal at a next ignition ON cycle.
• The counter upper limit is 39. Any counts exceeding 39 are ignored.“ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT.
Count up method B
JPNIA1828ZZ
JSNIA2179ZZ
JSNIA2180ZZ
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-409
< SYSTEM DESCRIPTION >
[PREMIUM AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• The counter increases by 1 if an error occurs when ignition switch is ON. The counter will not decrease even
if the condition is normal at the next ignition ON cycle.
• The counter upper limit is 50. Any counts exceeding 50 are ignored. “ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT.
Error item
Some error items may be displayed simultaneously according to the cause. If some error items are displayed
simultaneously, the detection of the cause can be performed by the combination of display items
Display type of occur-
rence frequency
Error history display item
Count up method A
CAN communication line, control unit (CAN), AV communication line, control unit (AV)
Count up method B
Other than the above
Error item
Description
Possible malfunction factor/Action to take
CAN COMM CIRCUIT
CAN communication malfunction is detect-
ed.
Perform diagnosis with CONSULT, and
then repair the malfunctioning parts accord-
ing to the diagnosis results.
Refer to
CONTROL UNIT (CAN)
CAN initial diagnosis malfunction is detect-
ed.
Replace the AV control unit if the malfunc-
tion occurs constantly.
Refer to
AV-611, "Removal and Installa-
.
CONTROL UNIT (AV)
AV communication circuit initial diagnosis
malfunction is detected.
FLASH-ROM Error Of Control Unit
AV control unit malfunction is detected.
Connection Of Gyro
Connection of G Sensor
CAN Controller Memory Error
Bluetooth
®
Module Connection Error
Sub CPU Connection Error
Audio connection error
DSP Connection Error
AV control unit malfunction is detected.
• If a disc can be played, there is a possi-
bility of an intermittent malfunction.
• Replace the AV control unit if the mal-
function occurs constantly.
Refer to
AV-611, "Removal and Installa-
DSP Communication Error
HDD Connection Error
AV control unit malfunction is detected.
• If the hard disk drive (HDD) is functioning
normally, there is a possibility of an inter-
mittent malfunction.
• Replace the AV control unit if the mal-
function occurs constantly.
Refer to
AV-611, "Removal and Installa-
HDD Read Error
HDD Write Error
HDD Communication Error
HDD Access Error
GPS Communication Error
GPS malfunction is detected.
• An intermittent error caused by strong ra-
dio interference may be detected unless
any symptom (GPS reception error, etc.)
occurs.
• Replace the AV control unit if the mal-
function occurs constantly.
Refer to
AV-611, "Removal and Installa-
GPS ROM Error
GPS RAM Error
GPS RTC Error
Unfinished configuration
The writing of configuration data is incom-
plete.
Write configuration data with CONSULT.
Refer to
CONTROL UNIT) : Work Procedure"
.
USB Controller Communication Error
USB connection malfunction is detected.
Check connection to USB connector is nor-
mal.
AV-410
< SYSTEM DESCRIPTION >
[PREMIUM AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DVD Mechanism Communication Error
AV control unit malfunction is detected.
• If DVD can be played, there is a possibil-
ity of an intermittent malfunction.
• Replace the AV control unit if the mal-
function occurs constantly.
Refer to
AV-611, "Removal and Installa-
Steer. Angle Sensor Calibration
Predictive course line center position ad-
justment of the steering angle sensor is in-
complete.
Adjust the predictive course line center po-
sition of the steering angle sensor.
Refer to
LINE CENTER POSITION ADJUSTMENT
: Work Procedure"
.
Front Display Connection Error
When one of the following is detected:
• malfunction is detected in front display
unit power supply and ground circuits.
• malfunction is detected in Serial commu-
nication circuits between AV control unit
and front display unit.
• Front display unit power supply or
ground circuit.
Refer to
.
• Serial communication circuits between
AV control unit and front display unit.
Refer to
.
• AV COMM CIRCUIT
• 2nd Display Connection Error
When one of the following is detected:
• malfunction is detected in video distribu-
tor power supply and ground circuits.
• malfunction is detected in headrest dis-
play unit (driver seat) power supply and
ground circuits.
• malfunction is detected in AV communi-
cation circuits between AV control unit
and headrest display unit (driver seat).
• Video distributor power supply or ground
.
• Headrest display unit (driver seat) power
supply or ground circuit.
Refer to
• AV communication circuits between AV
control unit and headrest display unit
(driver seat).
3rd Display Connection Error
When one of the following is detected:
• malfunction is detected in headrest dis-
play unit (passenger seat) power supply
and ground circuits.
• malfunction is detected in AV communi-
cation circuits between headrest display
unit (driver seat) and headrest display
unit (passenger seat).
• Headrest display unit (passenger seat)
power supply or ground circuit.
Refer to
• AV communication circuits between
headrest display unit (driver seat) and
headrest display unit (passenger seat).
Refer to
.
AM/FM antenna amplifier short to ground
Radio antenna amp. ON signal circuit mal-
function is detected.
Radio antenna amp. ON signal circuit be-
tween AV control unit and antenna amp.
Refer to
AM/FM antenna amplifier open
GPS Antenna Error
GPS antenna connection malfunction is de-
tected.
Check the connection of the GPS antenna
connector.
USB electric current Error
Detection of overcurrent in USB connector.
Check USB harness between AV control
unit and USB connector.
Refer to
Front Left Tweeter: open
Malfunction is detected in sound signal cir-
cuits between BOSE speaker amp. and in-
strument panel tweeter LH.
Sound signal circuits between BOSE
speaker amp. and instrument panel tweeter
LH.
Refer to
Front Left Tweeter: short
Front Left Tweeter: short to ground
Front Left Tweeter: short to battery
Front Right Tweeter: open
Malfunction is detected in sound signal cir-
cuits between BOSE speaker amp. and in-
strument panel tweeter RH.
Sound signal circuits between BOSE
speaker amp. and instrument panel tweeter
RH.
Refer to
Front Right Tweeter: short
Front Right Tweeter: short to ground
Front Right Tweeter: short to battery
Error item
Description
Possible malfunction factor/Action to take
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст