Nissan Pathfinder. Manual — part 228
BR-20
< REMOVAL AND INSTALLATION >
BRAKE PEDAL
REMOVAL AND INSTALLATION
BRAKE PEDAL
Exploded View
INFOID:0000000009177182
Removal and Installation
INFOID:0000000009177183
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-25, "Removal and Installation"
.
2. Remove sonar control unit (if equipped). Refer to
SN-34, "Removal and Installation"
.
3. Disconnect the stop lamp switch and ASCD cancel switch harness connectors.
4. Remove wire harness clips from brake pedal assembly.
5. Remove snap pin and clevis pin from clevis of brake booster.
6. Remove the brake pedal assembly.
CAUTION:
Support the brake booster and master cylinder to prevent contact with other components.
INSPECTION AFTER REMOVAL
1.
Clevis pin
2.
Brake pedal assembly
3.
Brake pedal pad
4.
Stop lamp switch
5.
ASCD cancel switch
6.
Clip
7.
Snap pin
AWFIA0951ZZ
BRAKE PEDAL
BR-21
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
• Check the following items and replace the brake pedal assembly if
necessary.
- Check the brake pedal upper rivet (made of aluminum) (A) for
deformation.
- Check the brake pedal for bend, damage, and cracks on the
welded parts.
- Check the overlap distance (X) of sub-bracket (B) and slide plate
(C).
INSTALLATION
Installation is in the reverse order of removal.
• Inspect the brake pedal height and play after installing the brake pedal to the vehicle. Adjust if necessary
refer to
.
Distance (X) : 5.5
± 0.5 mm (0.217 ± 0.020 in)
ALFIA0227ZZ
BR-22
< REMOVAL AND INSTALLATION >
BRAKE PIPING
BRAKE PIPING
FRONT
FRONT : Exploded View
INFOID:0000000009177184
1.
Master cylinder brake pipe assembly
(rear)
2.
Master cylinder brake pipe assembly
(front)
3.
ABS actuator to connector brake
pipe assembly - (RH)
4.
ABS actuator to connector brake
pipe assembly (LH)
5.
Brake pipe connector
6.
Brake pipe assembly (RH front)
7.
Brake pipe assembly (LH front)
8.
Master cylinder assembly
9.
Brake booster
10. ABS actuator and electric unit (con-
trol unit)
11. Lock plate
12. Front brake hose
13. Copper sealing washer
A.
To front brake hose
B.
To rear brake pipe
Front
AWFIA0952ZZ
BRAKE PIPING
BR-23
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
FRONT : Hydraulic Piping
INFOID:0000000009177185
CAUTION:
• Make sure that interference does not exist with other parts when turning steering both clockwise and
counterclockwise.
• Do not spill or splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend, twist or pull the brake hoses and piping.
• When removing components, cover connections to avoid dirt, dust, or other foreign matter from
entering the brake system.
• Do not reuse drained brake fluid.
• After installation of the ABS actuator and electric unit (control unit), refill brake system with new
brake fluid. Then bleed the air from the system. Refer to
BR-16, "Bleeding Brake System"
FRONT : Removal and Installation
INFOID:0000000009177186
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove wheels and tires using power tool.
2. Loosen the flare nut with a flare nut wrench and separate the brake tube from the hose.
CAUTION:
• Do not scratch the flare nut and the brake pipe.
• All brake hoses and pipes must be free from excessive bending, twisting and pulling.
1.
ABS actuator and electric unit (con-
trol unit)
2.
Front disc brake
3.
Master cylinder assembly
4.
Brake booster
5.
Connector
6.
Rear disc brake
A.
Brake tube
B.
Brake hose
: Flare nut
: Union bolt
AWFIA0895ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст