Nissan Pathfinder. Manual — part 963
PWO
POWER SOCKET
PWO-9
< REMOVAL AND INSTALLATION >
[POWER SOCKET]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
REMOVAL AND INSTALLATION
POWER SOCKET
Removal and Installation
INFOID:0000000009174832
FRONT CONSOLE POWER SOCKET, CONSOLE POWER SOCKET (IF EQUIPPED), REAR CON-
SOLE POWER SOCKET (IF EQUIPPED) or REAR CARGO POWER SOCKET
NOTE:
If unable to use the Tool because of power socket location or access to the harness connector, then further
removal of interior components may be required. Refer to
IP-24, "Removal and Installation"
IP-18, "Removal and Installation"
IP-29, "Disassembly and Assem-
(Rear Console Power Socket) or Rear Cargo Power Socket
INT-31, "LUGGAGE SIDE LOWER FIN-
ISHER : Removal and Installation"
Removal
1. Remove the fuse for the power socket.
2. Insert one side of the Tool (A) into one of the square holes inside
the power socket.
3. Lift up the handle of the Tool until the other side snaps into the
other square hole in the power socket.
4. Pull the power socket straight out with the Tool.
5. Disconnect the harness connector from the power socket.
6. Remove the ring from the power socket finisher while pressing
the pawls.
Installation
Installation is in the reverse order of removal.
NOTE:
Make sure to align the tab with the square notched area during
installation.
Tool number
: — (J-42059)
AWMIA1182GB
WKIA1035E
AWMIA1183GB
PWO-10
< PRECAUTION >
[AC 120 V OUTLET]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009726162
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Work
INFOID:0000000009174834
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
PWO
PREPARATION
PWO-11
< PREPARATION >
[AC 120 V OUTLET]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009174835
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-46534)
Trim tool set
Removing trim components
AWJIA0483ZZ
PWO-12
< SYSTEM DESCRIPTION >
[AC 120 V OUTLET]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009174836
Component Description
INFOID:0000000009174837
Inverter Unit
INFOID:0000000009174838
The inverter unit converts 12V DC to 120V AC.
AC 120V Outlet Main Switch
INFOID:0000000009174839
The AC outlet main switch allows operation of the inverter unit in 150W AC 120V mode.
AC 120V Outlet
INFOID:0000000009174840
The AC 120V outlet allow use of AC components up to 150W.
1.
Steering column
2.
AC 120V outlet main switch
3.
Rear air control
4.
AC 120V outlet
5.
Luggage side finisher lower LH
6.
Inverter unit (view with storage box
removed)
AWMIA1327ZZ
Component
Reference
Inverter unit
AC 120V outlet main switch
PWO-12, "AC 120V Outlet Main Switch"
AC 120V outlet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст