Nissan Pathfinder. Manual — part 780
LAN
AV BRANCH LINE CIRCUIT
LAN-73
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
AV BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000009174964
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the AV control unit for damage, bend and loose connection (unit
side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of AV control unit.
2. Check the resistance between the AV control unit harness connector terminals.
-
Mid audio system with BOSE audio system
-
Mid audio system without BOSE audio system
-
With premium audio system
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the AV control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the AV control unit. Refer to the following.
• Mid audio without BOSE:
AV-144, "AV CONTROL UNIT : Diagnosis Procedure"
• Mid audio with BOSE:
AV-305, "AV CONTROL UNIT : Diagnosis Procedure"
• Premium audio with navigation:
AV-549, "AV CONTROL UNIT : Diagnosis Procedure"
Is the inspection result normal?
YES (Present error)>>Replace the AV control unit. Refer to the following.
• Mid audio without BOSE:
AV-187, "Removal and Installation"
• Mid audio with BOSE:
AV-365, "Removal and Installation"
• Premium audio with navigation:
AV-611, "Removal and Installation"
YES (Past error)>>Error was detected in the AV control unit branch line.
NO
>> Repair the power supply and the ground circuit.
AV control unit harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M42
11
12
Approx. 54 – 66
AV control unit harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M124
11
12
Approx. 54 – 66
AV control unit harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M163
78
62
Approx. 54 – 66
LAN-74
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
DLC BRANCH LINE CIRCUIT
DLC BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000009174965
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the data link connector for damage, bend and loose connection
(connector side and harness side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
Check the resistance between the data link connector terminals.
Is the measurement value within the specification?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the data link connector branch line circuit.
NO
>> Repair the data link connector branch line.
Data link connector
Resistance (
Ω)
Connector No.
Terminal No.
M22
6
14
Approx. 54 – 66
LAN
DLC BRANCH LINE CIRCUIT (CAN COMMUNICATION CIRCUIT 1)
LAN-75
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DLC BRANCH LINE CIRCUIT (CAN COMMUNICATION CIRCUIT 1)
Diagnosis Procedure
INFOID:0000000009174966
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the data link connector for damage, bend and loose connection
(connector side and harness side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
Check the resistance between the data link connector terminals.
Is the measurement value within the specification?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the data link connector branch line circuit (CAN communication cir-
cuit 1 side).
NO
>> Repair the data link connector branch line (CAN communication circuit 1 side).
Data link connector
Resistance (
Ω)
Connector No.
Terminal No.
M22
6
14
Approx. 54 – 66
LAN-76
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
DLC BRANCH LINE CIRCUIT (CAN COMMUNICATION CIRCUIT 2)
DLC BRANCH LINE CIRCUIT (CAN COMMUNICATION CIRCUIT 2)
Diagnosis Procedure
INFOID:0000000009174967
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the data link connector for damage, bend and loose connection
(connector side and harness side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
Check the resistance between the data link connector terminals.
Is the measurement value within the specification?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the data link connector branch line circuit (CAN communication cir-
cuit 2 side).
NO
>> Repair the data link connector branch line (CAN communication circuit 2 side).
Data link connector
Resistance (
Ω)
Connector No.
Terminal No.
M22
13
12
Approx. 54 – 66
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст