Nissan Pathfinder. Manual — part 864
MWI-28
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
1: With base audio
2: Except base audio
Fail-Safe
INFOID:0000000009174243
FAIL-SAFE
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
34
(GR)
Ground
Vehicle speed signal
(8-pulse)
Output
Ignition
switch
ON
Speedometer operated
[When vehicle speed is ap-
prox. 25 MPH (40 km/h)]
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
38
(P)
Ground CAN-L
—
—
—
—
39
(L)
Ground CAN-H
—
—
—
—
41
(LG)
Ground Trip/Reset signal
Input
Ignition
switch
ON
Trip/Reset switch is pressed
0 V
Other than the above
5 V
42
(Y)
Ground
Illumination down switch
signal
Input
Ignition
switch
ON
Illumination switch down is
pressed
0 V
Other than the above
5 V
47
(BR)
Ground
Illumination up switch sig-
nal
Input
Ignition
switch
ON
Illumination switch up is
pressed
0 V
Other than the above
5 V
48
(G)
Ground Switch ground
—
—
—
—
49
(P)
Ground
Washer fluid level switch
signal
Input
Ignition
switch
ON
Washer fluid level switch ON
0 V
Washer fluid level switch OFF
5 V
52
(P)
Ground O/D OFF switch signal
Input
Ignition
switch
ON
O/D OFF switch is pressed
0 V
O/D OFF switch is released
Battery voltage
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
+
–
Signal name
Input/
Output
JSNIA0012GB
Function
Specifications
Speedometer
Reset to zero by suspending communication.
Tachometer
Engine coolant temperature gauge
Illumination control
When suspending communication, changes to nighttime mode.
Information display
Odo/trip meter
An indicated value is maintained at communications blackout.
Shift position indicator
The display turns OFF by suspending communication.
Warning messages
The display turns OFF by suspending communication.
Buzzer
The buzzer turns OFF by suspending communication.
MWI
COMBINATION METER
MWI-29
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DTC Index
INFOID:0000000009174244
Warning lamp/indicator lamp
ABS warning lamp
The lamp turns ON by suspending communication.
Slip indicator lamp
Brake warning lamp
O/D OFF indicator lamp
Malfunction indicator lamp
VDC OFF indicator lamp
EPS warning lamp
Low tire pressure warning lamp
The lamp blinking caused by suspending communication.
High beam indicator lamp
The lamp turns OFF by suspending communication.
Turn signal indicator lamp
Master warning lamp
Front lamp indicator lamp
Tow indicator lamp
Tail lamp indicator lamp
Air bag warning lamp
The lamp turns off when disconnected.
Charge warning lamp
Seat belt warning lamp
Security indicator lamp
Function
Specifications
Display contents of CONSULT
Diagnostic item is detected when...
Refer to
CAN COMM CIRCUIT
[U1000]
When combination meter is not transmitting or receiving CAN communication signal for 2
seconds or more.
CONTROL UNIT (CAN)
[U1010]
When detecting error during the initial diagnosis of the CAN controller of combination
meter.
VEHICLE SPEED CIRC
[B2205]
The abnormal vehicle speed signal is input from the ABS actuator and electric unit (control
unit) for 2 seconds or more.
TACHO METER
[B2267]
If ECM continuously transmits abnormal engine speed signals for 2 seconds or more.
WATER TEMP METER
[B2268]
If ECM continuously transmits abnormal engine coolant temperature signals for 60 sec-
onds or more.
MWI-30
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE)
List of ECU Reference
INFOID:0000000009174245
ECU
Reference
BCM
MWI
METER SYSTEM
MWI-31
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
WIRING DIAGRAM
METER SYSTEM
Wiring Diagram
INFOID:0000000009174246
ABNWA1828GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст