Nissan Pathfinder. Manual — part 1075
SPIRAL CABLE
SR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Set the spiral cable neutral position by carefully turning the spiral
cable clockwise to the end position. Turn the spiral cable counter-
clockwise 2.5 turns stopping when the locating pin (A) is at the top
most position, the triangles (C) are pointing at each other as shown
and the clear window (B) appears white.
NOTE:
If a new part is installed, the neutral position is already set with a
stopper in place and should not be adjusted after the stopper clip is
removed. Make sure the stopper clip is removed after the spiral
cable/steering angle sensor assembly is installed but before the
steering wheel is installed.
• During steering wheel installation, make sure the locating pin hole
(D) is aligned with the locating pin (A) of the spiral cable.
• Perform the neutral position adjustment for the steering angle sen-
sor. Refer to
CAUTION:
• The spiral cable may snap during steering operation if the spiral cable is installed in an improper
position.
• Do not overturn the spiral cable or go beyond the maximum number of turns allowed. This will cause
the cable to snap.
• The turn signal lever must be in the neutral position for spiral cable installation.
• Do not apply lubricant to the spiral cable.
• Do not allow oil, grease, detergent or water to come in contact with the spiral cable.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• If a malfunction is detected by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
AWHIA0467ZZ
SR-18
< REMOVAL AND INSTALLATION >
FRONT PASSENGER AIR BAG MODULE
FRONT PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000009176936
Removal and Installation
INFOID:0000000009176937
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Always work from the side of air bag module. Do not work in front of it.
• Do not use air tools or electric tools for servicing.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove the instrument panel assembly. Refer to
IP-15, "Removal and Installation"
.
3. Remove the front passenger air bag module screws.
1.
Instrument panel assembly
2.
Steering member assembly
3.
Front passenger air bag mod-
ule
A.
Front passenger air bag module
bolt to steering member assembly
(LH)
B.
Front passenger air bag module
bolt to steering member assembly
(RH)
C. Front passenger air bag mod-
ule screws
AWHIA0468ZZ
FRONT PASSENGER AIR BAG MODULE
SR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
4. Disconnect the front passenger air bag module pawls using a
suitable tool (A) as shown.
5. Lift up on the front passenger air bag module to remove the front
passenger air bag module as shown.
CAUTION:
• Always place the front passenger air bag module with the
pad side facing upward as shown.
: Upward
• Replace the front passenger air bag module if it has been
dropped or sustained an impact.
• Do not strike the front passenger air bag module.
• Do not insert any foreign objects (screwdriver, etc.) into the front passenger air bag module.
• Do not disassemble the front passenger air bag module.
• Do not expose the front passenger air bag module to temperatures exceeding 90
°C (194 °F).
• Do not allow oil, grease, detergent, or water to come in contact with the front passenger air bag
module.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse the front passenger air bag module bolts.
• Do not damage the front passenger air bag module harness during installation.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
AWHIA0477ZZ
AWHIA0403ZZ
JMHIA0009ZZ
SR-20
< REMOVAL AND INSTALLATION >
SIDE CURTAIN AIR BAG MODULE
SIDE CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000009176938
NOTE:
LH side shown, RH side similar.
Removal and Installation
INFOID:0000000009176939
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Always work from the side of air bag module. Do not work in front of it.
• Do not use air tools or electric tools for servicing.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove the headlining. Refer to
INT-27, "Removal and Installation"
.
1.
Side curtain air bag module
A. Side curtain air bag module
bracket supporting hook
B. Side curtain air bag module bolts
C. Clip
D. Front tether
ALHIA0252GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст