Nissan Pathfinder. Manual — part 1081
COMPONENT PARTS
SRC-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Front Door Satellite Sensor
INFOID:0000000009176964
The front door satellite sensors are located in the driver and passen-
ger doors. The front door satellite sensors send signals to the air bag
diagnosis sensor unit during a side collision. These sensors may be
identified by yellow connectors.
SRS Component Connectors
INFOID:0000000009176965
DIRECT CONNECT
The following SRS components use direct-connect style harness
connectors.
• Driver front air bag module
• Passenger front air bag module
• LH side curtain air bag module
• RH side curtain air bag module
• Front LH seat belt pre-tensioner
• Front RH seat belt pre-tensioner
Always pull up to release locking tab prior to removing connector
from SRS component.
Always push down to lock locking tab after installing connector to
SRS component. When locked, the locking tab is level with the con-
nector housing.
SLIDE DOUBLE LOCKING
• A new style slide double locking type connector is used on certain systems and components, especially
those related to air bag control systems.
• The slide double locking type connectors help prevent incomplete locking and accidental looseness or dis-
connection.
• The slide double locking type connectors are disconnected by pushing or pulling the slider. Refer to the fig-
ure below.
CAUTION:
• Do not pull the harness or wires when disconnecting the connector.
AWHIA0388ZZ
WHIA0103E
AAMIA0498GB
SRC-10
< SYSTEM DESCRIPTION >
SYSTEM
SYSTEM
SRS AIR BAG SYSTEM
SRS AIR BAG SYSTEM : System Diagram
INFOID:0000000009781499
SRS AIR BAG SYSTEM : System Description
INFOID:0000000009176967
• The air bag deploys if the air bag diagnosis sensor unit is activated while the ignition switch is in the ON or
START position.
• The collision modes for which supplemental restraint systems are activated are different among the SRS
systems. For example, the driver air bag module, front passenger air bag module and front seat belt pre-ten-
sioners are activated in a frontal collision but not in a side collision.
SRS Collision Modes
OCCUPANT CLASSIFICATION SYSTEM
AWHIA0419ZZ
SRS configuration
Frontal collision
Left side collision
Right side collision
Rollover
Drivers air bag module
x
—
—
—
Front passenger air bag module
x
—
—
—
Front LH seat belt pre-tensioner
x
—
—
x
Front RH seat belt pre-tensioner
x
—
—
x
Front LH side air bag module
—
x
—
—
Front RH side air bag module
—
—
x
—
LH side curtain air bag module
—
x
—
x
RH side curtain air bag module
—
—
x
x
SYSTEM
SRC-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
OCCUPANT CLASSIFICATION SYSTEM : System Diagram
INFOID:0000000009176968
OCCUPANT CLASSIFICATION SYSTEM : System Description
INFOID:0000000009176969
The occupant classification system (OCS) identifies different size occupants, out of position occupants, and
detects if a child seat is present in the front passenger seat. The OCS control unit (2) receives inputs from the
occupant classification sensors (1) (located inside the passenger seat cushion assembly). Depending on clas-
sification of the passenger, the OCS sends a signal to the air bag diagnosis sensor unit. The air bag diagnosis
sensor unit uses this signal and the seat belt buckle switch (passenger seat) signal to determine deployment
or non deployment of the passenger front air bag in the event of a collision. Depending on the signals
received, the air bag diagnosis sensor unit can disable the passenger front air bag completely. The OCS
(weight sensors) must be set to zero point using CONSULT after servicing the OCS system.
NOTE:
• CONSULT can be used to confirm when “zero point reset” for OCS is complete.
• Always perform zero point reset after the removal and installation of the seat or when disconnecting the
OCS control unit harness connector even if zero point reset has been completed in the past.
• If zero point reset is incomplete, the passenger air bag will be disabled and the passenger air bag off indica-
tor will be ON.
• In case of customer concern, CONSULT can be used to confirm the passenger air bag status (readiness).
Passenger Air Bag Status Conditions
NOTE:
Passenger does not meet Occupant Classification System specifications for passenger air bag activation.
Active Vent Function
When air bag diagnosis sensor unit has identified that the front passenger is not sitting in a suitable position,
the vent on the front passenger air bag module is opened. The pressure will be vented/released for the pas-
sengers safety.
AWHIA0390GB
Front Passenger Seat
(Condition)
PASS AIR BAG OFF Indicator
(Status)
Passenger Air Bag Status
(Readiness)
CONSULT Display
Seat occupied
OFF
Active (enabled)
ON
Seat occupied
NOTE
ON
Deactivated (disabled)
OFF
Seat empty
OFF
Deactivated (disabled)
OFF
SRC-12
< SYSTEM DESCRIPTION >
SYSTEM
SEAT BELT WARNING LAMP SYSTEM
SEAT BELT WARNING LAMP SYSTEM : System Diagram
INFOID:0000000009176970
AWHIA0391ZZ
ALHIA0028GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст