Almera Tino V10 (2003 year). Manual — part 131
DTC P0336 CKP SENSOR
EC-1115
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
CHECK CKP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 46 and CKP sensor terminal 1.
Refer to Wiring Diagram.
2.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK CRANKSHAFT POSITION SENSOR
Refer to
EC-1115, "Component Inspection"
.
OK or NG
OK
>> GO TO 6.
NG
>> Replace crankshaft position sensor.
6.
CHECK GEAR TOOTH
Visually check for chipping signal plate gear tooth.
OK or NG
OK
>> GO TO 7.
NG
>> Replace the signal plate.
7.
CHECK INTERMITTENT INCIDENT
Refer to
EC-1002, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
EBS013CU
CRANKSHAFT POSITION SENSOR
1.
Loosen the fixing bolt of the sensor.
2.
Disconnect crankshaft position sensor harness connector.
3.
Remove the sensor.
4.
Visually check the sensor for chipping.
Continuity should exist.
MBIB0864E
EC-1116
[YD (WITH EURO-OBD)]
DTC P0336 CKP SENSOR
5.
Check resistance as shown in the figure.
6.
If NG, replace crankshaft position sensor.
Removal and Installation
EBS013CV
CRANKSHAFT POSITION SENSOR
Refer to
EM-137, "OIL PAN AND OIL STRAINER"
.
Terminal No. (Polarity)
Resistance
Ω
[at 25
°
C (77
°
F)]
3 (+) - 1 (-)
Except 0
3 (+) - 2 (-)
Except 0 or
∞
2 (+) - 1 (-)
Except 0
MBIB0616E
DTC P0340 CMP SENSOR
EC-1117
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0340 CMP SENSOR
PFP:23731
Description
EBS013CW
The camshaft position sensor identifies a particular cylinder by
means of signals from the sensing plate (with five protrusions)
installed to the camshaft. The datum signal output is detected 90
°
signal and sent to the ECM.
ECM Terminals and Reference Value
EBS013CX
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
On Board Diagnosis Logic
EBS013CY
MBIB0618E
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage and Pulse Signal)
45
R
Camshaft position sensor
power supply
[Ignition switch ON]
Approximately 5.3V
47
B
Camshaft position sensor
[Engine is running]
●
Warm-up condition
●
Idle speed
0 - 6V
[Engine is running]
●
Warm-up condition
●
Engine speed is 2,000 rpm
0 - 6V
66
W
Camshaft position sensor
ground
[Ignition switch ON]
Approximately 0.3V
67
B
Sensor ground
(Sensors shield circuit)
[Ignition switch ON]
Approximately 0.3V
MBIB0877E
MBIB0878E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0340
Camshaft position sensor
circuit
Camshaft position sensor signal is not detect
by the ECM when engine is running.
●
Harness or connectors
(The sensor circuit is open or shorted.)
●
Camshaft position sensor
EC-1118
[YD (WITH EURO-OBD)]
DTC P0340 CMP SENSOR
DTC Confirmation Procedure
EBS013CZ
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for at least 5 seconds.
If engine could not start, keep ignition switch at START position
for 5 seconds.
4.
If 1st trip DTC is detected, go to
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
SEF817Y
DTC P0340 CMP SENSOR
EC-1119
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
EBS013D0
YEC505A
EC-1120
[YD (WITH EURO-OBD)]
DTC P0340 CMP SENSOR
Diagnostic Procedure
EBS013D1
1.
CHECK STARTING SYSTEM
Turn ignition switch to START position.
Yes or No
Yes
>> GO TO 2.
No
>> Check starting system. (Refer to SC-13, “STARTING SYSTEM”.)
2.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten body ground screw. Refer to
.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace ground connection.
3.
CHECK CMP SENSOR POWER SUPPLY CIRCUIT
1.
Disconnect camshaft position (CMP) sensor harness connector.
2.
Turn ignition switch ON.
3.
Check voltage between CMP sensor terminal 1 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
Does the engine turn over?
Does the starter motor operate?
MBIB0915E
MBIB0907E
Voltage: Approximately 5.3V
MBIB1095E
DTC P0340 CMP SENSOR
EC-1121
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
CHECK CMP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 66 and CMP sensor terminal 2.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK CMP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 47 and CMP sensor terminal 3.
Refer to Wiring Diagram.
2.
Also check harness for short to ground or short to power.
OK or NG
OK
>> GO TO 6.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.
CHECK CAMSHAFT POSITION SENSOR
Refer to
EC-1121, "Component Inspection"
.
OK or NG
OK
>> GO TO 7.
NG
>> Replace camshaft position sensor.
7.
CHECK INTERMITTENT INCIDENT
Refer to
EC-1002, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
EBS013D2
CAMSHAFT POSITION SENSOR
1.
Loosen the fixing bolt of the sensor.
2.
Disconnect camshaft position sensor harness connector.
3.
Remove the sensor.
4.
Visually check the sensor for chipping.
Continuity should exist.
Continuity should exist.
MBIB0647E
EC-1122
[YD (WITH EURO-OBD)]
DTC P0340 CMP SENSOR
5.
Check resistance as shown in the figure.
6.
If NG, replace camshaft position sensor.
Removal and Installation
EBS013D3
CAMSHAFT POSITION SENSOR
Refer to
.
Terminal No. (Polarity)
Resistance
Ω
[at 25
°
C (77
°
F)]
3 (+) - 1 (-)
Except 0
3 (+) -2 (-)
2 (+) - 1 (-)
Except 0 or
∞
MBIB0616E
DTC P0341 CMP SENSOR
EC-1123
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0341 CMP SENSOR
PFP:23731
Description
EBS013D4
The camshaft position sensor identifies a particular cylinder by
means of signals from the sensing plate (with five protrusions)
installed to the camshaft. The datum signal output is detected 90
°
signal and sent to the ECM.
ECM Terminals and Reference Value
EBS013D5
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
On Board Diagnosis Logic
EBS013D6
MBIB0618E
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage and Pulse Signal)
45
R
Camshaft position sensor
power supply
[Ignition switch ON]
Approximately 5.3V
47
B
Camshaft position sensor
[Engine is running]
●
Warm-up condition
●
Idle speed
0 - 6V
[Engine is running]
●
Warm-up condition
●
Engine speed is 2,000 rpm
0 - 6V
66
W
Camshaft position sensor
ground
[Ignition switch ON]
Approximately 0.3V
67
B
Sensor ground
(Sensors shield circuit)
[Ignition switch ON]
Approximately 0.3V
MBIB0877E
MBIB0878E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0341
Camshaft position sensor
circuit range/performance
Camshaft position sensor signal is not in the
normal pattern when engine is running.
●
Harness connectors
(The sensor circuit is opener shorted.)
●
Camshaft position sensor
●
Signal plate
EC-1124
[YD (WITH EURO-OBD)]
DTC P0341 CMP SENSOR
DTC Confirmation Procedure
EBS013D7
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for at least 5 seconds.
If engine could not start, keep ignition switch at START position
for 5 seconds.
4.
If 1st trip DTC is detected, go to
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
SEF817Y
DTC P0341 CMP SENSOR
EC-1125
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
EBS013D8
YEC505A
EC-1126
[YD (WITH EURO-OBD)]
DTC P0341 CMP SENSOR
Diagnostic Procedure
EBS013D9
1.
CHECK STARTING SYSTEM
Turn ignition switch to START position.
Yes or No
Yes
>> GO TO 2.
No
>> Check starting system. (Refer to SC-13, “STARTING SYSTEM”.)
2.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten body ground screw. Refer to
.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace ground connection.
3.
CHECK CMP SENSOR POWER SUPPLY CIRCUIT
1.
Disconnect camshaft position (CMP) sensor harness connector.
2.
Turn ignition switch ON.
3.
Check voltage between CMP sensor terminal 1 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
Does the engine turn over?
Does the starter motor operate?
MBIB0915E
MBIB0907E
Voltage: Approximately 5.3V
MBIB1095E
DTC P0341 CMP SENSOR
EC-1127
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
CHECK CMP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 66 and CMP sensor terminal 2.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK CMP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 47 and CMP sensor terminal 3.
Refer to Wiring Diagram.
2.
Also check harness for short to ground or short to power.
OK or NG
OK
>> GO TO 6.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.
CHECK CAMSHAFT POSITION SENSOR
Refer to
EC-1128, "Component Inspection"
.
OK or NG
OK
>> GO TO 7.
NG
>> Replace camshaft position sensor.
7.
CHECK CAMSHAFT (EXHAUST)
Check the following.
●
Accumulation of debris to the signal plate of camshaft rear end
●
Chipping signal plate of camshaft rear end
OK or NG
OK
>> GO TO 8.
NG
>> Remove debris and clean the signal plate of camshaft
rear end or replace camshaft.
8.
CHECK INTERMITTENT INCIDENT
Refer to
EC-1002, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Continuity should exist.
Continuity should exist.
MBIB0990E
EC-1128
[YD (WITH EURO-OBD)]
DTC P0341 CMP SENSOR
Component Inspection
EBS013DA
CAMSHAFT POSITION SENSOR
1.
Loosen the fixing bolt of the sensor.
2.
Disconnect camshaft position sensor harness connector.
3.
Remove the sensor.
4.
Visually check the sensor for chipping.
5.
Check resistance as shown in the figure.
6.
If NG, replace camshaft position sensor.
Removal and Installation
EBS013DB
CAMSHAFT POSITION SENSOR
Refer to
.
MBIB0647E
Terminal No. (Polarity)
Resistance
Ω
[at 25
°
C (77
°
F)]
3 (+) - 1 (-)
Except 0
3 (+) - 2 (-)
2 (+) - 1 (-)
Except 0 or
∞
MBIB0616E
DTC P0380 GLOW RELAY
EC-1129
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0380 GLOW RELAY
PFP:25230
On Board Diagnosis Logic
EBS013DC
DTC Confirmation Procedure
EBS013DD
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Wait at least 5 seconds.
4.
If 1st trip DTC is detected, go to
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0380
Glow relay circuit
An excessively low voltage is sent to ECM
through glow relay.
●
Harness or connectors
(The glow relay circuit is open or shorted.)
●
Glow relay
An excessively low voltage is sent to ECM
through glow relay.
●
Harness or connectors
(The glow relay circuit is shorted.)
●
Glow relay
SEF817Y
EC-1130
[YD (WITH EURO-OBD)]
DTC P0380 GLOW RELAY
Wiring Diagram
EBS013DE
MBWA0620E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст