Almera Tino V10 (2003 year). Manual — part 18
TROUBLE DIAGNOSIS — BASIC INSPECTION
AT-273
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
7.
CHECK VEHICLE MOVE
1.
Move selector lever to “D”, “2” and “1” positions and check if
vehicle creeps forward.
2.
Does vehicle creep forward in all three positions?
Yes or No
Yes
>> GO TO
.
No
>>
●
Mark the box on the DIAGNOSTIC WORKSHEET.
●
GO TO
AT-320, "7. Vehicle Does Not Creep Forward
.
●
Continue ROAD TEST. Refer to
.
3. CRUISE TEST
●
Check all items listed in Parts 1 through 3.
With CONSULT-II
●
Using CONSULT-II, conduct a cruise test and record the result.
●
Print the result and ensure that shifts and lock-ups take place as per Shift Schedule.
CONSULT-II Setting Procedure
1.
Turn ignition switch “OFF”.
2.
Connect CONSULT-II to data link connector, which is located in
left side lower dash panel.
3.
Turn ignition switch “ON”.
4.
Touch “START (NISSAN BASED VHCL)”.
SAT773B
SAT601J
PAIA0070E
MBIB0233E
AT-274
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — BASIC INSPECTION
5.
Touch “A/T”.
6.
Touch “DATA MONITOR”.
7.
Touch “MAIN SIGNALS” or “TCM INPUT SIGNALS”.
8.
Select “Numerical Display”, “Barchart Display” or “Line Graph
Display”.
9.
Touch “SETTING” to recording condition (“AUTO TRIG” or
“MANU TRIG”) and touch “BACK”.
10. Touch “Start”.
SAT014K
SAT971J
SAT175K
SAT973J
TROUBLE DIAGNOSIS — BASIC INSPECTION
AT-275
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
11. When performing cruise test, touch “RECORD”.
12. After finishing cruise test part 1, touch “STOP”.
13. Touch “STORE” and touch “BACK”.
SAT134K
SAT135K
SAT987J
SAT974J
AT-276
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — BASIC INSPECTION
14. Touch “DISPLAY”.
15. Touch “PRINT”.
16. Check the monitor data printed out.
17. Continue cruise test part 2 and 3.
Without CONSULT-II
●
Throttle position sensor can be checked by voltage across termi-
nals 41 and 42 of TCM.
SAT975J
SCIA0710E
TROUBLE DIAGNOSIS — BASIC INSPECTION
AT-277
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Cruise Test — Part 1
1.
CHECK STARTING GEAR (D
1
) POSITION
1.
Drive vehicle for approx. 10 minutes to warm engine oil and ATF up to operating
temperature.
2.
Park vehicle on flat surface.
3.
Set overdrive control switch to “ON” position.
4.
Move selector lever to “P” position.
5.
Start engine.
6.
Move selector lever to “D” position.
7.
Accelerate vehicle by constantly depressing accelerator pedal
halfway.
8.
Does vehicle start from D
1
?
Read gear position.
Yes or No
Yes
>> GO TO 2
No
>>
●
GO TO
AT-321, "8. Vehicle Cannot Be Started From
.
●
Continue ROAD TEST. Refer to
.
ATF operating temperature: 50 - 80
°
C (122 - 176
°
F)
SAT774B
SAT775B
SAT495G
AT-278
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — BASIC INSPECTION
2.
CHECK SHIFT UP (D
1
TO D
2
)
Does A/T shift from D
1
to D
2
at the specified speed?
Read gear position, throttle opening and vehicle speed.
Yes or No
Yes
>> GO TO 3
No
>>
●
GO TO
AT-324, "9. A/T Does Not Shift: D
.
●
Continue ROAD TEST. Refer to
.
3.
CHECK SHIFT UP (D
2
TO D
3
)
Does A/T shift from D
2
to D
3
at the specified speed?
Read gear position, throttle position and vehicle speed.
Yes or No
Yes
>> GO TO 4
No
>>
●
GO TO
AT-326, "10. A/T Does Not Shift: D
.
●
Continue ROAD TEST. Refer to
.
4.
CHECK SHIFT UP (D
3
TO D
4
)
Does A/T shift from D
3
to D
4
at the specified speed?
Read gear position, throttle position and vehicle speed.
Yes or No
Yes
>> GO TO 5
No
>>
●
GO TO
AT-328, "11. A/T Does Not Shift: D
.
●
Continue ROAD TEST. Refer to
.
Specified speed when shifting from D
1
to D
2
:
Refer to
.
SAT954I
Specified speed when shifting from D
2
to D
3
:
Refer to
.
SAT955I
Specified speed when shifting from D
3
to D
4
:
Refer to
.
SAT956I
TROUBLE DIAGNOSIS — BASIC INSPECTION
AT-279
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
5.
CHECK LOCK-UP (D
4
TO D
4
L/U)
Does A/T perform lock-up at the specified speed?
Read vehicle speed, throttle position when lock-up duty becomes 94%.
Yes or No
Yes
>> GO TO 6
No
>>
●
GO TO
AT-330, "12. A/T Does Not Perform Lock-up"
.
●
Continue ROAD TEST. Refer to
.
6.
CHECK HOLD LOCK-UP
Does A/T hold lock-up condition for more than 30 seconds?
Yes or No
Yes
>> GO TO 7
No
>>
●
GO TO
AT-330, "13. A/T Does Not Hold Lock-up Condition"
.
●
Continue ROAD TEST. Refer to
.
7.
CHECK SHIFT DOWN (D
4
L/U TO D
4
)
1.
Release accelerator pedal.
2.
Is lock-up released when accelerator pedal is released?
Yes or No
Yes
>> GO TO 8
No
>>
●
GO TO
AT-332, "14. Lock-up Is Not Released"
.
●
Continue ROAD TEST. Refer to
.
8.
CHECK SHIFT DOWN (D
4
TO D
3
)
1.
Decelerate vehicle by applying foot brake lightly.
2.
Does engine speed return to idle smoothly when A/T is shifted from D
4
to D
3
?
Read gear position and engine speed.
Yes or No
Yes
>> 1. Stop vehicle.
2. GO TO
AT-280, "Cruise Test — Part 2"
.
No
>>
●
GO TO
AT-332, "15. Engine Speed Does Not Return
.
●
Continue ROAD TEST. Refer to
.
Specified speed when lock-up occurs:
Refer to
.
SAT957I
SAT958I
SAT959I
AT-280
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — BASIC INSPECTION
Cruise Test — Part 2
1.
CHECK STARTING GEAR (D
1
) POSITION
1.
Confirm overdrive control switch is in “ON” position.
2.
Confirm selector lever is in “D” position.
3.
Accelerate vehicle by half throttle again.
4.
Does vehicle start from D
1
?
Read gear position.
Yes or No
Yes
>> GO TO 2
No
>>
●
GO TO
AT-334, "16. Vehicle Does Not Start From D
.
●
Continue ROAD TEST. Refer to
.
2.
CHECK SHIFT UP AND SHIFT DOWN (D
3
TO D
4
TO D
2
)
1.
Accelerate vehicle to 80 km/h (50 MPH) as shown in illustration.
2.
Release accelerator pedal and then quickly depress it fully.
3.
Does A/T shift from D
4
to D
2
as soon as accelerator pedal is depressed fully?
Read gear position and throttle position.
Yes or No
Yes
>> GO TO 3
No
>>
●
GO TO
AT-324, "9. A/T Does Not Shift: D
.
●
Continue ROAD TEST. Refer to
.
3.
CHECK SHIFT UP (D
2
TO D
3
)
Does A/T shift from D
2
to D
3
at the specified speed?
Read gear position, throttle position and vehicle speed.
Yes or No
Yes
>> GO TO 4
No
>>
●
GO TO
AT-326, "10. A/T Does Not Shift: D
.
●
Continue ROAD TEST. Refer to
.
SAT495G
SAT404H
Specified speed when shifting from D
2
to D
3
:
Refer to
.
SAT960I
TROUBLE DIAGNOSIS — BASIC INSPECTION
AT-281
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
4.
CHECK SHIFT UP (D
3
TO D
4
) AND ENGINE BRAKE
Release accelerator pedal after shifting from D
2
to D
3
.
Does A/T shift from D
3
to D
4
and does vehicle decelerate by engine brake?
Read gear position, throttle position and vehicle speed.
Yes or No
Yes
>> 1. Stop vehicle.
2. GO TO
AT-282, "Cruise Test — Part 3"
.
No
>>
●
GO TO
AT-328, "11. A/T Does Not Shift: D
.
●
Continue ROAD TEST. Refer to
.
SAT405H
AT-282
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — BASIC INSPECTION
Cruise Test — Part 3
1.
CHECK SHIFT DOWN (D
4
TO D
3
)
1.
Confirm overdrive control switch is in “ON” position.
2.
Confirm selector lever is in “D” position.
3.
Accelerate vehicle using half-throttle to D
4
.
4.
Release accelerator pedal.
5.
Set overdrive control switch to “OFF” position while driving in D
4
.
6.
Does A/T shift from D
4
to D
3
(O/D OFF)?
Read gear position and vehicle speed.
Yes or No
Yes
>> GO TO 2
No
>>
●
GO TO
AT-334, "17. A/T Does Not Shift: D
, When Overdrive Control Switch “ON”
.
●
Continue ROAD TEST. Refer to
.
SAT812A
SAT813A
SAT776BA
TROUBLE DIAGNOSIS — BASIC INSPECTION
AT-283
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
2.
CHECK ENGINE BRAKE
Does vehicle decelerate by engine brake?
Yes or No
Yes
>> GO TO 3
No
>>
●
GO TO
AT-332, "15. Engine Speed Does Not Return
.
●
Continue ROAD TEST. Refer to
.
3.
CHECK SHIFT DOWN (D
3
TO D
2
)
1.
Move selector lever from “D” to “2” position while driving in D
3
(O/D OFF).
2.
Does A/T shift from D
3
(O/D OFF) to 2
2
?
Read gear position.
Yes or No
Yes
>> GO TO 4
No
>>
●
GO TO
AT-335, "18. A/T Does Not Shift: D
.
●
Continue ROAD TEST. Refer to
.
4.
CHECK ENGINE BRAKE
Does vehicle decelerate by engine brake?
Yes or No
Yes
>> GO TO 5
No
>>
●
GO TO
AT-332, "15. Engine Speed Does Not Return
.
●
Continue ROAD TEST. Refer to
.
5.
CHECK SHIFT DOWN
1.
Move selector lever from “2” to “1” position while driving in 2
2
.
2.
Does A/T shift from 2
2
to 1
1
position?
Read gear position.
Yes or No
Yes
>> GO TO 6
No
>>
●
GO TO
AT-336, "19. A/T Does Not Shift: 2
.
●
Continue ROAD TEST. Refer to
.
SAT776BA
SAT791GA
SAT791GA
SAT778B
AT-284
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — BASIC INSPECTION
6.
CHECK ENGINE BRAKE
Does vehicle decelerate by engine brake?
Yes or No
Yes
>> 1. Stop vehicle.
2. Perform self-diagnosis.
Refer to
AT-252, "SELF-DIAGNOSTIC PROCEDURE
,
No
>>
●
GO TO
AT-337, "20. Vehicle Does Not Decelerate By
.
●
Continue ROAD TEST. Refer to
.
SAT778B
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
AT-285
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
PFP:00000
Symptom Chart
ECS009A2
Numbers are arranged in order of inspection.
Perform inspections starting with number one and work up.
Symptom
Condition
Diagnostic Item
Reference Page
Engine cannot start in “P” and “N”
positions.
AT-313, "2. Engine Cannot Be Started
In “P” and “N” Position"
ON vehicle
1. Ignition switch and starter
EL-11, “Power Supply
Routing”, SC-13, “Start-
ing System”.
2. Control cable adjustment
AT-412, "Control Cable
Adjustment"
3. PNP switch adjustment
AT-412, "Park/Neutral
Position (PNP) Switch
Adjustment"
Engine starts in position other than
“N” and “P” positions.
AT-313, "2. Engine Cannot Be Started
In “P” and “N” Position"
ON vehicle
1. Control cable adjustment
AT-412, "Control Cable
Adjustment"
2. PNP switch adjustment
AT-412, "Park/Neutral
Position (PNP) Switch
Adjustment"
Transaxle noise in “P” and “N” posi-
tions.
ON vehicle
1. Fluid level
2. Line pressure test
3. Throttle position sensor (Accelerator
pedal position (APP) sensor)
AT-356, "ACCELE
RATOR PEDAL POSI-
TION (APP) SENSOR"
4. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTR
AT-347, "VEHICLE
SPEED SENSOR - A/T
(REVOLUTION SEN-
SOR)"
AT-352, "DTC VEHICLE
SPEED SENSOR MTR"
5. Engine speed signal
OFF vehicle
6. Oil pump
7. Torque converter
AT-421, "Locations of
Adjusting Shims, Needle
Bearings, Thrust Washers
and Snap Rings"
Vehicle moves when changing into “P”
position, or parking gear does not dis-
engage when shifted out of “P” posi-
tion.
AT-313, "3. In “P” Position, Vehicle
Moves Forward Or Backward When
Pushed"
ON vehicle
1. Control cable adjustment
AT-412, "Control Cable
Adjustment"
OFF vehicle
2. Parking components
AT-482, "Output Shaft,
Idler Gear, Reduction Pin-
ion Gear and Bearing
Retainer"
Vehicle runs in “N” position.
AT-315, "4. In “N” Position, Vehicle
Moves"
ON vehicle
1. Control cable adjustment
AT-412, "Control Cable
Adjustment"
OFF vehicle
2. Forward clutch
AT-468, "Forward and
Overrun Clutches"
3. Reverse clutch
4. Overrun clutch
AT-286
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Vehicle will not run in “R” position (but
runs in “D”, “2” and “1” positions).
Clutch slips.
Very poor acceleration.
AT-317, "6. Vehicle Does Not Creep
Backward In “R” Position"
ON vehicle
1. Control cable adjustment
AT-412, "Control Cable
Adjustment"
2. Line pressure test
3. Line pressure solenoid valve
AT-392, "LINE PRES-
SURE SOLENOID
VALVE"
4. Control valve assembly
AT-410, "Control Valve
Assembly and Accumula-
tors"
OFF vehicle
5. Reverse clutch
6. High clutch
7. Forward clutch
AT-468, "Forward and
Overrun Clutches"
8. Overrun clutch
AT-468, "Forward and
Overrun Clutches"
9. Low & reverse brake
Vehicle braked when shifting into “R”
position.
ON vehicle
1. Fluid level
2. Control cable adjustment
AT-412, "Control Cable
Adjustment"
3. Line pressure test
4. Line pressure solenoid valve
AT-392, "LINE PRES-
SURE SOLENOID
VALVE"
5. Control valve assembly
AT-410, "Control Valve
Assembly and Accumula-
tors"
OFF vehicle
6. High clutch
7. Brake band
AT-487, "Band Servo Pis-
ton Assembly"
8. Forward clutch
AT-468, "Forward and
Overrun Clutches"
9. Overrun clutch
AT-468, "Forward and
Overrun Clutches"
Symptom
Condition
Diagnostic Item
Reference Page
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
AT-287
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Sharp shock in shifting from “N” to “D”
position.
ON vehicle
1. Engine idling rpm
EC-936, "Idle Speed and
Ignition Timing"
2. Throttle position sensor Accelerator
pedal position (APP) sensor Adjustment
AT-356, "ACCELE
RATOR PEDAL POSI-
TION (APP) SENSOR"
3. Line pressure test
4. A/T fluid temp sen circ and TCM pow
sour
AT-381, "BATT/FLUID
TEMP SEN (A/T FLUID
TEMP SENSOR CIR-
CUIT AND TCM POWER
SOURCE)"
5. Engine speed signal
6. Line pressure solenoid valve
AT-392, "LINE PRES-
SURE SOLENOID
VALVE"
7. Control valve assembly
AT-410, "Control Valve
Assembly and Accumula-
tors"
8. Accumulator N-D
AT-410, "Control Valve
Assembly and Accumula-
tors"
OFF vehicle
9. Forward clutch
AT-468, "Forward and
Overrun Clutches"
Vehicle will not run in “D” and “2” posi-
tions (but runs in “1” and “R” posi-
tions).
ON vehicle
1. Control cable adjustment
AT-412, "Control Cable
Adjustment"
OFF vehicle
2. Low one-way clutch
AT-421, "Locations of
Adjusting Shims, Needle
Bearings, Thrust Washers
and Snap Rings"
Vehicle will not run in “D”, “1”, “2” posi-
tions (but runs in “R” position). Clutch
slips. Very poor acceleration.
AT-320, "7. Vehicle Does Not Creep
Forward In “D”, “2” Or “1” Position"
ON vehicle
1. Fluid level
2. Line pressure test
3. Line pressure solenoid valve
AT-392, "LINE PRES-
SURE SOLENOID
VALVE"
4. Control valve assembly
AT-410, "Control Valve
Assembly and Accumula-
tors"
5. Accumulator N-D
AT-410, "Control Valve
Assembly and Accumula-
tors"
OFF vehicle
6. Reverse clutch
7. High clutch
8. Forward clutch
AT-468, "Forward and
Overrun Clutches"
9. Forward one-way clutch
10. Low one-way clutch
AT-421, "Locations of
Adjusting Shims, Needle
Bearings, Thrust Washers
and Snap Rings"
Symptom
Condition
Diagnostic Item
Reference Page
AT-288
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Clutches or brakes slip somewhat in
starting.
ON vehicle
1. Fluid level
2. Control cable adjustment
AT-412, "Control Cable
Adjustment"
3. Throttle position sensor (Accelerator
pedal position (APP) sensor)
AT-356, "ACCELE
RATOR PEDAL POSI-
TION (APP) SENSOR"
4. Line pressure test
5. Line pressure solenoid valve
AT-392, "LINE PRES-
SURE SOLENOID
VALVE"
6. Control valve assembly
AT-410, "Control Valve
Assembly and Accumula-
tors"
7. Accumulator N-D
AT-410, "Control Valve
Assembly and Accumula-
tors"
OFF vehicle
8. Forward clutch
AT-468, "Forward and
Overrun Clutches"
9. Reverse clutch
10. Low & reverse brake
11. Oil pump
12. Torque converter
AT-421, "Locations of
Adjusting Shims, Needle
Bearings, Thrust Washers
and Snap Rings"
Excessive creep.
ON vehicle
1. Engine idling rpm
EC-936, "Idle Speed and
Ignition Timing"
No creep at all.
AT-317, "6. Vehicle Does Not Creep
Backward In “R” Position"
and
320, "7. Vehicle Does Not Creep For-
ward In “D”, “2” Or “1” Position"
ON vehicle
1. Fluid level
2. Line pressure test
3. Control valve assembly
AT-410, "Control Valve
Assembly and Accumula-
tors"
OFF vehicle
4. Forward clutch
AT-468, "Forward and
Overrun Clutches"
5. Oil pump
6. Torque converter
AT-421, "Locations of
Adjusting Shims, Needle
Bearings, Thrust Washers
and Snap Rings"
Symptom
Condition
Diagnostic Item
Reference Page
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст