Nissan Qashqai (2022 year). Manual in english — page 27
CAUTION
.
Do not ground accessories di-
rectly to the battery terminal.
Doing so will bypass the variable
voltage control system and the
vehicle battery may not charge
completely.
.
Use electrical accessories with
the engine running to avoid dis-
charging the vehicle battery.
The variable voltage control system mea-
sures the amount of electrical discharge
from the battery and controls voltage
generated by the generator.
SDI1881
1.
Alternator
2.
Drive belt auto-tensioner
3.
Crankshaft pulley
4.
Air conditioner compressor
5.
Water pump
WARNING
Be sure the ignition switch is in the
OFF or LOCK position before servi-
cing drive belts. The engine could
rotate unexpectedly.
1. Visually inspect the belt for signs of
unusual wear, cuts, fraying or loosen-
ess. If the belt is in poor condition or
loose, have it replaced or adjusted. It is
recommended you visit a NISSAN
dealer for this service.
2. Have the belt condition checked reg-
ularly.
Do-it-yourself
8-13
VARIABLE VOLTAGE CONTROL SYSTEM
DRIVE BELT
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-14
Do-it-yourself
WARNING
Be sure the engine and ignition
switch are off and that the parking
brake is applied.
CAUTION
Be sure to use the correct socket to
remove the spark plugs. An incorrect
socket can damage the spark plugs.
SDI2670
REPLACING SPARK PLUGS
If replacement is required, it is recom-
mended you visit a NISSAN dealer for this
service.
Iridium platinum-tipped spark
plugs
It is not necessary to replace the iridium
platinum-tipped spark plugs as frequently
as the conventional type spark plugs
since they will last much longer. Follow
the maintenance schedule shown in the
“9. Maintenance and schedules” section.
Do not reuse the iridium platinum-tipped
spark plugs by cleaning or regapping.
Always replace spark plugs with recom-
mended or equivalent ones.
SPARK PLUGS
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WAI0158X
AIR DUCT REMOVAL
1.
Remove the clip
with a suitable tool.
2.
While pulling off the lock
, pull out the
clip
and pull up the air duct
.
WAI0159X
1.
Remove the clips
and open the air
cleaner filter cover
.
2.
Pull up the air cleaner filter
.
AIR CLEANER FILTER REPLACEMENT
WARNING
.
Operating the engine with the air
cleaner filter off can cause you or
others to be burned. The air
cleaner filter not only cleans the
intake air, it also stops flame if
the engine backfires. If the air
cleaner filter is not installed and
the engine backfires, you could
be burned. Never drive with the
air cleaner filter off. Be cautious
working on the engine when the
air cleaner filter is off.
.
Never pour fuel into the throttle
body or attempt to start the
engine with the air cleaner re-
moved. Doing so could result in
serious injury.
Do-it-yourself
8-15
AIR CLEANER
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-16
Do-it-yourself
CLEANING
If your windshield is not clear after using
the windshield washer or if a wiper blade
chatters when running, wax or other
material may be on the blade or wind-
shield.
Clean the outside of the windshield with a
washer solution or a mild detergent. Your
windshield is clean if beads do not form
when rinsing with clear water.
Clean each blade by wiping it with a cloth
soaked in a washer solution or a mild
detergent. Then rinse the blade with clear
water. If your windshield is still not clear
after cleaning the blades and using the
wiper, replace the blades.
CAUTION
Worn windshield wiper blades can
damage the windshield and impair
driver vision.
SDI2359
REPLACING
Replace the wiper blades if they are worn.
1. Lift the wiper arm away from the
windshield.
2. Push and hold the release tab
, and
move the wiper blade down the wiper
arm
.
3. Insert the new wiper blade onto the
wiper arm until a click sounds.
4. Rotate the wiper blade so that the
dimple is in the groove.
CAUTION
.
After wiper blade replacement,
return the wiper arm to its origi-
nal position; otherwise it may be
damaged when the hood is
opened.
.
Make sure the wiper blades con-
tact the glass; otherwise the arm
may be damaged from wind
pressure.
WINDSHIELD WIPER BLADES
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SDI2693
Be careful not to clog the washer nozzle
. This may cause improper windshield
washer operation. If the nozzle is clogged,
remove any objects with a needle or small
pin
. Be careful not to damage the
nozzle.
It is recommended you contact a NISSAN
dealer if checking or replacement is
required.
If the brakes do not operate properly, it is
recommended you have the brakes
checked by a NISSAN dealer.
SELF-ADJUSTING BRAKES
Your vehicle is equipped with self-adjust-
ing brakes.
The disc-type brakes self-adjust every
time the brake pedal is applied.
WARNING
Have your brake system checked if
the brake pedal height does not
return to normal. It is recommended
you visit a NISSAN dealer for this
service.
BRAKE PAD WEAR WARNING
The disc brake pads have audible wear
warnings. When a brake pad requires
replacement, it will make a high pitched
scraping sound when the vehicle is in
motion. This scraping sound will first
occur only when the brake pedal is
depressed. After more wear of the brake
pad, the sound will always be heard even
if the brake pedal is not depressed. Have
the brakes checked as soon as possible if
the wear warning sound is heard.
Under some driving or climate conditions,
Do-it-yourself
8-17
REAR WINDOW WIPER BLADE
BRAKES
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-18
Do-it-yourself
occasional brake squeak, squeal or other
noise may be heard. Occasional brake
noise during light to moderate stops is
normal and does not affect the function
or performance of the brake system.
Proper brake inspection intervals
should be followed.
For additional infor-
mation, see the maintenance schedule
shown in the “9. Maintenance and sche-
dules” section.
JVM0386X
ENGINE COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified
on the fuse box cover. This could
damage the electrical system or
electronic control units or cause a
fire.
If any electrical equipment does not
operate, check for an open fuse.
1. Be sure the ignition switch is turned
off, and the headlight switch is in the
OFF position (if so equipped) or the
AUTO position and the headlights are
OFF.
2. Open the engine hood.
3. Remove the fuse/fusible link box cov-
er by using a suitable tool and pushing
the tab.
4. Locate the fuse that needs to be
replaced.
5. Remove the fuse using the fuse puller
located in the passenger compart-
ment fuse box.
FUSES
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SDI1753
Type A
SDI1754
Type B
6. If the fuse is open
, replace it with a
new fuse
.
7. If a new fuse also opens, have the
electrical system checked and re-
paired. It is recommended you visit a
NISSAN dealer for this service.
JVM0444X
The holder
also contains the fuses.
It is recommended you visit a NISSAN
dealer for checking and/or replacing.
Fusible links
If any electrical equipment does not
operate and the fuses are in good condi-
tion, check the fusible links. If any of these
fusible links are melted, replace only with
genuine NISSAN parts.
For checking and replacing the fusible
links, it is recommended you visit a
NISSAN dealer.
Do-it-yourself
8-19
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-20
Do-it-yourself
JVM0387X
PASSENGER COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified
on the fuse box cover. This could
damage the electrical system or
electronic control units or cause a
fire.
If any electrical equipment does not
operate, check for an open fuse.
1. Be sure the ignition switch is turned
off, and the headlight switch is in the
OFF position (if so equipped) or the
AUTO position and the headlights are
OFF.
2. Remove the fuse box cover.
3. Remove the fuse with the fuse puller
.
SDI1754
4. If the fuse is open
, replace it with a
new fuse
.
5. If a new fuse also opens, have the
electrical system checked and re-
paired. It is recommended you visit a
NISSAN dealer for this service.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
JVM0415X
Extended storage fuse switch (if so
equipped)
To reduce battery drain, the extended
storage fuse switch comes from the
factory switched off. Prior to delivery of
your vehicle, the switch is pushed in
(switched on) and should always remain
on.
If the extended storage fuse switch is not
pushed in (switched on), the meter may
display a warning message. See “21. Ship-
ping Mode On Push Storage Fuse warn-
ing” (P.2-33).
If any electrical equipment does not
operate, remove the extended storage
fuse switch and check for an open fuse.
NOTE:
If the extended storage fuse switch
malfunctions or if the fuse is open, it is
not necessary to replace the switch. In
this case, remove the extended storage
fuse switch and replace it with a new
fuse of the same rating.
How to remove the extended storage
fuse switch:
1. To remove the extended storage fuse
switch, be sure the ignition switch is in
the OFF or LOCK position.
2. Be sure the headlights are off. (See
“Headlight switch” (P.2-52) or “Intelli-
gent Auto Headlight system” (P.2-52).)
3. Remove the fuse box cover.
4. Pinch the locking tabs
found on
each side of the extended storage
fuse switch.
5. Pull the extended storage fuse switch
straight out from the fuse box
.
CAUTION
.
Be careful not to allow children to
swallow the battery and removed
parts.
.
An improperly disposed battery
can harm the environment. Al-
ways confirm local regulations
for battery disposal.
.
When changing batteries, do not
let dust or oil get on the compo-
nents.
.
There is danger of explosion if the
lithium battery is incorrectly re-
placed. Replace only with the
same or equivalent type.
Do-it-yourself
8-21
KEY FOB BATTERY REPLACEMENT
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-22
Do-it-yourself
JVM0381X
To replace the battery:
1. Insert a small screwdriver into the slit
to open the lid. Use a cloth to
protect the casing.
2. Replace the battery with a new one.
Recommended battery: CR2032 or
equivalent
.
Do not touch the internal circuit
and electric terminals as doing so
could cause a malfunction.
.
Hold the battery by the edges.
Holding the battery across the
contact points will seriously deplete
the storage capacity.
.
Make sure that the
+
side faces the
bottom of the case
.
3. Close the lid securely.
4. Operate the buttons to check its
operation.
See a NISSAN dealer if you need assis-
tance for replacement.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including inter-
ference that may cause undesired op-
eration.
Note: Changes or modifications not
expressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Ca-
nada licence-exempt RSS standard(s).
Operation is subject to the following
two conditions: (1) this device may not
cause interference, and (2) this device
must accept any interference, including
interference that may cause undesired
operation of the device.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CAUTION
.
Be careful not to allow children to
swallow the battery and removed
parts.
.
An improperly disposed battery
can harm the environment. Al-
ways confirm local regulations
for battery disposal.
.
When changing batteries, do not
let dust or oil get on the compo-
nents.
.
There is danger of explosion if the
lithium battery is incorrectly re-
placed. Replace only with the
same or equivalent type.
SDI2451
Replace the battery in the Intelligent Key
as follows:
1. Remove the mechanical key from the
Intelligent Key.
2. Insert a small screwdriver into the slit
of the corner and twist it to separate
the upper part from the lower part.
Use a cloth to protect the casing.
3. Replace the battery with a new one.
Recommended battery:
CR2032 or equivalent
.
Do not touch the internal circuit
and electric terminals as doing so
could cause a malfunction.
.
Hold the battery by the edges.
Holding the battery across the
contact points will seriously deplete
the storage capacity.
.
Make sure that the
+
side faces the
bottom of the case.
Do-it-yourself
8-23
INTELLIGENT KEY BATTERY REPLACEMENT
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-24
Do-it-yourself
SDI2452
4. Align the tips of the upper and lower
parts , and then push them together
until it is securely closed.
5. Operate the buttons to check its
operation.
If you need any assistance for replace-
ment, it is recommended you visit a
NISSAN dealer for this service.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including inter-
ference that may cause undesired op-
eration.
Note: Changes or modifications not
expressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Ca-
nada licence-exempt RSS standard(s).
Operation is subject to the following
two conditions: (1) this device may not
cause interference, and (2) this device
must accept any interference, including
interference that may cause undesired
operation of the device.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WAI0093X
1.
Front parking light/Daytime running
light/Front turn signal light (LED type)
2.
Front turn signal light (bulb type)
3.
Headlight (high-beam)
4.
Headlight (low-beam)
5.
Front side marker light
6.
Map light and front room light
7.
Room light
8.
Side turn signal light (if so equipped)
9.
Front fog light (if so equipped)
10.
Cargo light
11.
High-mounted stop light
12.
Rear combination light (tail light, stop
light, rear turn signal light)
13.
Rear side marker light
14.
License plate light
15.
Reverse light/Tail light
HEADLIGHTS
Fog may temporarily form inside the lens
of the exterior lights in the rain or in a car
wash. A temperature difference between
the inside and the outside of the lens
causes the fog. This is not a malfunction.
If large drops of water collect inside the
lens, it is recommended you visit a NISSAN
dealer for servicing.
Do-it-yourself
8-25
LIGHTS
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-26
Do-it-yourself
Replacing
LED headlight model:
If LED headlight replacement is required,
it is recommended that you visit a NISSAN
dealer for this service.
Halogen headlight model:
The headlight is a semi-sealed beam type
which uses a replaceable headlight (halo-
gen) bulb.
CAUTION
.
Do not leave the bulb out of the
headlight reflector for a long
period of time. Dust, moisture,
smoke, etc. entering the head-
light body may affect bulb per-
formance.
.
High pressure halogen gas is
sealed inside the halogen bulb.
The bulb may break if the glass
envelope is scratched or the bulb
is dropped.
.
Only touch the base when hand-
ling the bulb. Never touch the
glass envelope. Touching the
glass envelope could significantly
affect bulb life and/or headlight
performance.
.
Aiming is not necessary after
replacing the bulb. When aiming
adjustment is necessary, it is
recommended you visit a NISSAN
dealer for this service.
Use the same number and wattage as
originally installed as shown in the chart.
WAI0094X
Low-beam/High-beam:
1.
Disconnect the battery negative cable.
2.
Disconnect the electrical connector
from the rear end of the bulb.
3.
Remove the headlight bulb
by turning it
counterclockwise. Do not shake or rotate
the bulb when removing it.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
4.
Install the new bulb in the reverse order of
removal.
EXTERIOR AND INTERIOR LIGHTS
Item
Wattage (W)
Bulb No.
Headlight high beam (bulb type)
65
H9
Headlight low beam (bulb type)
55
H11
Headlight high/low beams (LED type)*
LED
-
Front turn signal light*
21 or LED
WY21W or -
Front parking light*
LED
-
Front side marker light*
LED
-
Front fog light (if so equipped)*
35
H8
Side turn signal light (if so equipped)*
LED
-
Daytime running light*
LED
-
Rear combination light*
Turn signal light
21
W21W
Stop/tail light
LED
—
Back-up
16
W16W
Rear side marker light*
LED
-
License plate light*
5
W5W
Map light*
LED
-
Vanity mirror light (if so equipped)*
1.8
-
High-mounted stop light*
LED
-
Room light
8
-
Cargo light
5
-
Glove box light*
1.4
-
*:
It is recommended you visit a NISSAN dealer for replacement.
NOTE: It is recommended that you check with the Parts Department at a NISSAN dealer for the
latest information about parts.
Do-it-yourself
8-27
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-28
Do-it-yourself
SDI2306
Replacement procedures
:
REMOVE
:
INSTALL
All other lights are either type A, B, C, D or
E. When replacing a bulb, first remove the
lens and/or cover.
SDI1499A
Room light
SDI2653
Cargo light
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст