Nissan X-Trail 32. Manual — part 1277
FAX-100
< REMOVAL AND INSTALLATION >
[4WD]
FRONT DRIVE SHAFT
FRONT DRIVE SHAFT
MR20DD
MR20DD : Exploded View
INFOID:0000000010824416
LEFT SIDE
JSDIA5389ZZ
Circular clip
Dust shield
Housing
Snap ring
Spider assembly
Stopper ring
Boot band
Boot
Shaft
Damper band
Dinamic damper
Joint sub-assembly
Dust shield
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
: Always replace after every disassembly.
FRONT DRIVE SHAFT
FAX-101
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
RIGHT SIDE
MR20DD : Removal and Installation
INFOID:0000000010824417
REMOVAL
Left Side
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove wheel sensor from steering knuckle. Refer to
BRC-212, "FRONT WHEEL SENSOR : Removal
JSDIA5460GB
Dust shield
Joint sub-assembly
Circular clip
Boot band
Boot
Shaft
Damper band
Dynamic damper
Stopper ring
Spider assembly
Snap ring
Housing
Dust shield
Support bearing
Retainer
Support bearing bracket
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
FAX-102
< REMOVAL AND INSTALLATION >
[4WD]
FRONT DRIVE SHAFT
3.
Remove lock plate
from strut assembly.
• LHD: Refer to
BR-24, "FRONT : Exploded View"
.
• RHD: Refer to
BR-88, "FRONT : Exploded View"
4.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work.
• LHD (1 PISTON TYPE): Refer to
BR-51, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• LHD (2 PISTON TYPE): Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
• RHD (1 PISTON TYPE): Refer to
BR-111, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• RHD (2 PISTON TYPE): Refer to
BR-116, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
FAX-72, "Removal and Installation"
.
6.
Remove cotter pin, adjusting cap and then loosen wheel hub
lock nut, using a hub lock nut wrench (A) (SST: KV40104000).
7.
Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub and bearing assembly from drive
shaft.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive
shaft cannot be separated even after performing the above pro-
cedure.
8.
Remove wheel hub lock nut.
9.
Remove transverse link from steering knuckle and front suspension member. Refer to
10. Separate steering outer socket from steering knuckle. Refer to
ST-22, "Removal and Installation"
JSDIA3795ZZ
JSDIA2708ZZ
JPDIG0070ZZ
FRONT DRIVE SHAFT
FAX-103
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
11. Remove drive shaft from wheel hub and bearing assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle.
• Be careful not to overextend slide joint.
12. Remove drive shaft from transaxle assembly.
• Use the drive shaft attachment (A) (SST: KV40107500) and a
sliding hammer (B) (commercial service tool) while inserting
tip of the drive shaft attachment between housing and tran-
saxle assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle when
removing drive shaft. Also be careful not to overextend
slide joint.
• Confirm that the circular clip is attached to the drive
shaft.
Right Side
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove wheel sensor from steering knuckle. Refer to
BRC-212, "FRONT WHEEL SENSOR : Removal
3.
Remove lock plate
from strut assembly.
• LHD: Refer to
BR-24, "FRONT : Exploded View"
.
• RHD: Refer to
BR-88, "FRONT : Exploded View"
4.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work.
• LHD (1 PISTON TYPE): Refer to
BR-51, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• LHD (2 PISTON TYPE): Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
• RHD (1 PISTON TYPE): Refer to
BR-111, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• RHD (2 PISTON TYPE): Refer to
BR-116, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
FAX-72, "Removal and Installation"
.
JSDIA5562ZZ
JPDIF0004ZZ
JSDIA3795ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст