Nissan X-Trail 32. Manual — part 97
BCS-104
< BASIC INSPECTION >
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
BASIC INSPECTION
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
Description
INFOID:0000000010688611
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-
ment.
NOTE:
If “Before Replace ECU” of “Read / Write Configuration” cannot be used, use the “Manual Configuration” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, always perform “Read / Write Configuration” or “Manual Configuration” with
CONSULT. Or not doing so, BCM control function does not operate normally.
• Complete the procedure of “Read / Write Configuration” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• If you set incorrect “Read / Write Configuration” or “Manual Configuration”, incidents might occur.
NOTE:
• When replacing BCM, perform the system initialization (NATS) (if equipped).
• When replacing BCM, perform the system initialization (CAN gateway).
Work Procedure
INFOID:0000000010688612
1.
SAVING VEHICLE SPECIFICATION (BCM)
CONSULT Configuration
Perform “Before Replace ECU” of “Read/ Write Configuration” to save or print current vehicle specification.
Refer to
NOTE:
If “Before Replace ECU” of “Read/Write Configuration” cannot be used, use the “Manual Configuration” after
replacing BCM.
>> GO TO 2.
2.
SAVING VEHICLE SPECIFICATION (CAN GATEWAY)
CONSULT Configuration
Perform “Before Replace ECU” of “Read / Write Configuration” to save or print current vehicle specification.
NOTE:
If “Before Replace ECU” of “Read / Write Configuration” cannot be used, use the “Manual Configuration” after
replacing BCM.
>> GO TO 3.
3.
REPLACE BCM
Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
>> GO TO 4.
4.
WRITING VEHICLE SPECIFICATION (BCM)
CONSULT Configuration
Perform “After Replace ECU” of “Read / Write Configuration” or “Manual Configuration” to write vehicle speci-
fication. Refer to
>> GO TO 5.
5.
INITIALIZE BCM (NATS) (IF EQUIPPED)
BCS
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
BCS-105
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Perform BCM initialization. (NATS)
>> GO TO 6.
6.
INITIALIZE CAN GATEWAY
Perform CAN GATEWAY initialization. Refer to
>> WORK END
BCS-106
< BASIC INSPECTION >
CONFIGURATION (BCM)
CONFIGURATION (BCM)
Description
INFOID:0000000010688613
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.
Configuration has three functions as follows.
NOTE:
Manual setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting cannot be changed)
For some models and specifications, the automatic setting item may not be displayed.
CAUTION:
When replacing BCM, always perform “Re/programming, Configuration” with CONSULT. Or not doing
so, BCM control function does not operate normally.
• Complete the procedure of “Read / Write Configuration” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “Read / Write Configuration” except for new BCM.
• If you set incorrect “Read / Write Configuration”, incidents might occur.
Work Procedure
INFOID:0000000010688614
1.
WRITING MODE SELECTION
CONSULT Configuration
Select “Re/programming, Configuration” of BCM.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.
PERFORM “AFTER REPLACE ECU” OF “READ / WRITE CONFIGURATION”
CONSULT Configuration
Perform “After Replace ECU” of “Read / Write Configuration”.
>> WORK END
3.
PERFORM “MANUAL CONFIGURATION”
CONSULT Configuration
1.
Select “Manual Configuration”.
2.
Identify the correct model and configuration list. Refer to
.
3.
Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
NOTE:
If items are not displayed, touch “Next”. Refer to
value.
4.
Touch “Next”.
5.
Touch “OK”.
CAUTION:
Make sure to select “OK” even if the indicated configuration of brand new BCM is same as the
desirable configuration. If not, configuration which is set automatically by selecting vehicle model
cannot be memorized.
6.
Check that the configuration has been successfully written and touch “End”.
Function
Description
Read / Write Configuration
Before Replace ECU
• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.
After Replace ECU
Writes the vehicle configuration with saved data.
Manual Configuration
Writes the vehicle configuration with manual selection.
BCS
CONFIGURATION (BCM)
BCS-107
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
>> GO TO 4.
4.
OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Configuration list
INFOID:0000000010688615
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally if
the setting is not correct.
WITH INTELLIGENT KEY SYSTEM
⇔
: Items which confirm vehicle specifications
WITHOUT INTELLIGENT KEY SYSTEM
SETTING ITEM
NOTE
Items
Setting value
SUPER LOCK
WITH
⇔
WITHOUT
—
H/L WASHER
WITHOUT
⇔
MODE1
• WITHOUT: Without headlamp washer
• MODE1: With headlamp washer
HLW CYL SW INP NMB OF TIM
MODE1
⇔
MODE2
• MODE1: Except for Europe (LHD) models with head-
lamp washer
• MODE2: For Europe (LHD) models with headlamp
washer
THEFT ALM AREA
WITHOUT
⇔
MODE4
• WITHOUT: Except for Europe (RHD) models
• MODE4: For Europe (RHD) models
HANDLE
LHD
⇔
RHD
—
ECM TYPE
MODE1
⇔
MODE2
• MODE1: For MR engine or QR engine models
• MODE2: Except for MR engine or QR engine models
DONGLE
WITH
⇔
WITHOUT
• WITH: For Europe (RHD) models
• WITHOUT: Except for Europe (RHD) models
TPMS
WITH
⇔
WITHOUT
—
HBA SYSTEM
WITH
⇔
WITHOUT
• WITH: With high beam assist system
• WITHOUT: Without high beam assist system
Key Fob Type
LCK/UNLCK/PBD
—
ALT TYPE
MODE1
⇔
MODE4
• MODE1: For MR engine or QR engine models
• MODE4: Except for MR engine or QR engine models
TRANSMISSION
MT with ABS
⇔
AT with ABS
• MT with ABS: M/T models
• AT with ABS: Except M/T models
SETTING ITEM
NOTE
Items
Setting value
AUTO LIGHT
WITHOUT
⇔
MODE5
• WITHOUT: Without auto light
• MODE5: With auto light
SUPER LOCK
WITH
⇔
WITHOUT
—
H/L WASHER
WITHOUT
⇔
MODE1
• WITHOUT: Without headlamp washer
• MODE1: With headlamp washer
HLW CYL SW INP NMB OF TIM
MODE1
⇔
MODE2
• MODE1: Except for Europe (LHD) models with head-
lamp washer
• MODE2: For Europe (LHD) models with headlamp
washer
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст