Nissan X-Trail 32. Manual — part 1971
SRC-52
< DTC/CIRCUIT DIAGNOSIS >
B0094 CRASH ZONE SENSOR
B0094 CRASH ZONE SENSOR
DTC Description
INFOID:0000000010688481
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0094–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
[B0094–23, B0094–24, B0094–25, B0094–28]
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
[B0094–81, B0094–93]
• Connection malfunction of harness or connector
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
[B0094–86]
• Air bag diagnosis sensor unit and crash zone sensor is different from the part specified
[B0094–88]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010688482
WARNING:
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0094–11
CRASH ZONE SENS
[Center Frontal Restraints Sensor (Subfault)]
Crash zone sensor circuit is shorted to ground
B0094–23
Lower limit value malfunction of crash zone sensor
B0094–24
Upper limit value malfunction of crash zone sensor
B0094–25
Diagnosis malfunction of crash zone sensor
B0094–28
Offset malfunction of crash zone sensor
B0094–81
Communication malfunction of crash zone sensor
B0094–86
Crash zone sensor is out of the specified specification
B0094–88
Crash zone sensor circuit is open
B0094–93
Reset malfunction of crash zone sensor
B0094 CRASH ZONE SENSOR
SRC-53
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0094–86]>> GO TO 4.
Other than the above>> GO TO 2.
2.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 3.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace malfunctioning harness and connector.
4.
REPLACE CRASH ZONE SENSOR
1.
Replace crash zone. Refer to
SR-31, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-38, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-54
< DTC/CIRCUIT DIAGNOSIS >
B0096 B-PILLAR SATELLITE SENSOR
B0096 B-PILLAR SATELLITE SENSOR
DTC Description
INFOID:0000000010688483
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0096–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of B-pillar satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0096–23, B0096–24, B0096–25, B0096–28]
• Internal malfunction of B-pillar satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0096–81, B0096–93]
• Connection malfunction of harness or connector
• Internal malfunction of B-pillar satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0096–86]
• Air bag diagnosis sensor unit and B-pillar satellite sensor RH is different from the part specified
[B0096–88]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of B-pillar satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010688484
WARNING:
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0096–11
B-PILLAR SAT SEN RH
[Right Frontal Restraints Sensor 1(Subfault)]
B-pillar satellite sensor RH circuit is shorted to ground
B0096–23
Lower limit value malfunction of B-pillar satellite sensor RH
B0096–24
Upper limit value malfunction of B-pillar satellite sensor RH
B0096–25
Diagnosis malfunction of B-pillar satellite sensor RH
B0096–28
Offset malfunction of B-pillar satellite sensor RH
B0096–81
Communication malfunction of B-pillar satellite sensor RH
B0096–86
B-pillar satellite sensor RH is out of the specified specification
B0096–88
B-pillar satellite sensor RH circuit is open
B0096–93
Reset malfunction of B-pillar satellite sensor RH
B0096 B-PILLAR SATELLITE SENSOR
SRC-55
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0096–86] >> GO TO 4.
Other than the above >> GO TO 2.
2.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 3.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace malfunctioning harness and connector.
4.
REPLACE B-PILLAR SATELLITE SENSOR RH
1.
Replace B-pillar satellite sensor RH. Refer to
SR-33, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-38, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст