Nissan X-Trail 32. Manual — part 1766
RF-50
< REMOVAL AND INSTALLATION >
REAR SUNROOF GLASS
Removal and Installation
INFOID:0000000010735430
REMOVAL
CAUTION:
Always work with a helper.
1.
Remove sunroof unit assembly. Refer to
RF-57, "Removal and Installation"
.
2.
Remove rear sunroof glass fixing screws
, and then remove
rear sunroof glass.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
After installing the rear sunroof glass, perform the leak test and check that there is no malfunction.
NOTE:
After installation, carry out fitting adjustment. Refer to
.
Adjustment
INFOID:0000000010735431
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
NOTE:
Dimension (B) is given assuming that the glass upper side status is (+), and the glass lower side status is (
−
)
relative to the roof panel.
Rear drain hose RH
Rear drain connector RH
Front sunroof bracket LH
Rear sunroof glass
Drain assembly
: Clip
: N·m (kg-m, in-lb)
,
,
,
,
,
,
,
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
: Vehicle front
JMKIB2808ZZ
JMKIB2827GB
Roof panel
Glass lid
Rear sunroof glass
REAR SUNROOF GLASS
RF-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
1.
Loosen rear sunroof glass fixing screws.
2.
Adjust the clearance of rear sunroof glass and roof panel according to the fitting standard dimension.
3.
To prevent rear sunroof glass from moving after adjustment, first tighten the fixing screws of front left, and
then tighten the fixing screws of rear right.
4.
Tighten remaining fixing screws, being careful to prevent rear sunroof glass from moving.
NOTE:
After adjustment the sunroof unit assembly, perform additional service. Refer to
.
Portion
A
B
−
6.5 – 8.1 mm
(0.256 – 0.319 in)
(
−
2.2) – (+0.8) mm
[(
−
0.087) – (+0.031) in]
−
6.5 – 8.1 mm
(0.256 – 0.319 in)
(
−
2.2) – (+0.8) mm
[(
−
0.087) – (+0.031) in]
−
6.5 – 8.1 mm
(0.256 – 0.319 in)
(
−
1.5) – (+1.5) mm
[(
−
0.059) – (+0.059) in]
RF-52
< REMOVAL AND INSTALLATION >
SUNROOF MOTOR ASSEMBLY
SUNROOF MOTOR ASSEMBLY
Exploded View
INFOID:0000000010735432
Front sunroof bracket RH
Glass lid
Wind deflector
Rear sunroof bracket RH
Side trim RH
Sunroof unit assembly
Front drain hose RH
Sunroof motor assembly
Front drain connector RH
Harness connector assembly
Front drain connector LH
Sunshade motor assembly
Front drain hose LH
Side trim LH
Rear sunroof bracket LH
Sunshade
Rear drain connector LH
Rear drain hose LH
JMKIB2824GB
SUNROOF MOTOR ASSEMBLY
RF-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
Removal and Installation
INFOID:0000000010735433
REMOVAL
CAUTION:
• Before removing sunroof motor, check that glass lid is fully closed.
• After removing sunroof motor, never attempt to rotate sunroof motor assembly as a single unit.
1.
Disconnect battery cable from negative terminal.
2.
Remove headlining to make work space. Refer to
INT-37, "Removal and Installation"
3.
Disconnect harness connector
from sunroof motor assembly.
4.
Remove sunroof motor assembly fixing screws
, and then
remove sunroof motor assembly.
INSTALLATION
CAUTION:
Before installing the sunroof motor assembly, always place the link and wire assembly in the symmet-
rical and fully closed position.
1.
Move the sunroof motor assembly laterally a little so that the gear is completely engaged into the wire on
the sunroof unit assembly and mounting surface becomes parallel. Then secure the sunroof motor
assembly with screws.
2.
Install headlining.
NOTE:
After installation sunroof motor assembly, perform additional service. Refer to
Rear drain hose RH
Rear drain connector RH
Front sunroof bracket LH
Rear sunroof glass
Drain assembly
: Clip
: N·m (kg-m, in-lb)
,
,
,
,
,
,
,
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB2840ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст