Nissan X-Trail 32. Manual — part 2208
PRECAUTIONS
WT-5
< PRECAUTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NOTE:
• Do not close driver door because the steering wheel locks when driver door is closed.
• The auto acc function is adapted to this vehicle. For this reason, even when the ignition switch is turned
to OFF position, the accessory power source does not turned OFF and continues to be supplied for a
certain amount of time.
6.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
7.
Perform the necessary repair operation.
8.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from OFF position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
9.
Perform self-diagnosis check of all control units using CONSULT.
Service Notice and Precautions for TPMS
INFOID:0000000010715053
• Low tire pressure warning lamp turns ON when tire pressure is less than warning tire pressure value. Adjust
tire pressure for all wheels to the specified value. Refer to
TPMS reset operation. Refer to
.
• Low tire pressure warning lamp blinks for 1 minute, then turns ON when occurring any malfunction or no
sensor(s) except low tire pressure. Erase the self-diagnosis memories for Tire Pressure Monitoring System
(TPMS), or register the ID to turn low tire pressure warning lamp OFF. For ID registration, refer to
.
• ID registration is required when replacing or rotating tires and/or wheels, replacing tire pressure sensor or
BCM. Refer to
.
• Be sure to replace seal, washer, valve core and valve cap of tire pressure sensor, when removing tire pres-
sure sensor from wheel. Refer to
Replacing seal and washer, valve core and valve cap of tire pressure sensor is recommended, when replac-
ing each tire by reaching the wear limit. Refer to
.
• Never apply excessive force to an inflator not to damage valve stem and tire pressure sensor when adjusting
tire pressure.
• Jack up the vehicle in order not to damage tire pressure sensor when extracting all the tire air on the vehicle
(e.g. when filling up work of N
2
gas to tire). For supporting points for lifting and jacking point, refer to
"Garage Jack and Safety Stand and 2-Pole Lift"
.
• Because the tire pressure sensor conforms to Europe radio law, the following items must be observed.
- The sensor may be used only in Europe.
- It may not be used in any method other than the specified method.
- It must not be disassembled or modified.
• Never attach tire pressure sensor of other cars. Tire Pressure Monitoring System (TPMS) does not function
if specified Genuine NISSAN tire pressure sensor is not attached.
Service Notice and Precautions for Road Wheel
INFOID:0000000010715054
• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it on the specified vehicle only.
• Use Genuine NISSAN parts for the road wheels, valve caps and wheel nuts.
• Always use them after adjusting the wheel balance. For the balance weights, use Genuine NISSAN alumi-
num wheel weights.
• Use caution when handling the aluminum wheels, because they can be easily scratched. When removing
dirt, do not use any abrasives, a wire brush, or other items that may scratch the coating. Use a neutral deter-
gent if a detergent is needed.
• After driving on roads scattered with anti-icing salts, wash off the wheels completely.
• When installing road wheels onto the vehicle, always wipe off any dirt or foreign substances to prevent them
from being trapped between the contact surfaces of wheel.
• Never apply oil to nut and bolt threads.
• When tightening the valve cap there is a risk of damaging the valve cap if a tool is used. Tighten by hand.
WT-6
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000010715055
Tool number
Tool name
Description
KV48105501
(NI-4032)
Tire pressure sensor activation tool
Tire pressure sensor wake-up procedure and
ID registration
JSEIA0650ZZ
COMPONENT PARTS
WT-7
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000010715056
LHD MODELS
Wheel assembly
Behind instrument panel (LH)
No.
Component parts
Function
Rear wheel sensor (RH)
Location of wheel is specified due to the synchronism of wheel sensor position and
tire pressure sensor position.
ABS actuator and electric unit (control unit)
Mainly transmits the following signals to BCM via CAN communication.
• Vehicle speed signal (ABS)
Front wheel sensor (RH)
Location of wheel is specified due to the synchronism of wheel sensor position and
tire pressure sensor position.
Front wheel sensor (LH)
JSEIA0867ZZ
WT-8
< SYSTEM DESCRIPTION >
COMPONENT PARTS
RHD MODELS
Combination meter
Mainly receives the following signals from BCM via CAN communication.
• Low tire pressure warning lamp signal
• Low tire pressure wheel location signal
• TPMS malfunction warning lamp signal
Mainly transmits the following signals to BCM via CAN communication.
• TPMS reset signal
Rear wheel sensor (LH)
Location of wheel is specified due to the synchronism of wheel sensor position and
tire pressure sensor position.
Tire pressure sensor
.
BCM
.
No.
Component parts
Function
Wheel assembly
Behind of grove box (LH)
JSEIA0938ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст