Nissan X-Trail 32. Manual — part 2112
TM-406
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CONTROL CABLE
CONTROL CABLE
MR20DD
MR20DD : Exploded View
INFOID:0000000010622592
MR20DD : Removal and Installation
INFOID:0000000010622593
REMOVAL
CAUTION:
• Always apply the parking brake before performing removal and installation.
• Be careful not to cut your hand on heat insulator edges.
1.
Turn ignition switch OFF.
2.
Shift the selector lever to “P” position.
3.
Remove battery tray. Refer to
PG-148, "EXCEPT FOR R9M : Removal and Installation"
Control cable
Lock plate
Transaxle assembly
Manual lever
Bracket A
Bracket B
Grommet
CVT shift selector assembly
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSDIA5630GB
CONTROL CABLE
TM-407
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Remove the control cable nut (
) and remove the control cable
from the manual lever
.
5.
Remove the lock plate
and remove the control cable
from
bracket .
6.
Remove the center console. Refer to
.
7.
Disconnect the tip
of control cable from the CVT shift selector
assembly.
8.
Remove socket
from CVT shift selector assembly.
CAUTION:
Never damage pawl of socket.
9.
Disengage the pawls (
) of the grommet
, and pull down-
wards to remove.
10. Lift up the vehicle.
11. Remove the exhaust front tube. Refer to
12. Remove the heat plate fixtures
.
: Vehicle front
JSDIA5183ZZ
: Vehicle front
JSDIA5184ZZ
JSDIA5661ZZ
JSDIA5182ZZ
: Vehicle front
JSDIA5214ZZ
TM-408
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CONTROL CABLE
13. Remove the control cable
from bracket
.
14. Remove the control cable from the vehicle.
INSTALLATION
Note the followings and install in the reverse order of removal.
• From below the vehicle, press the grommet
into place until the
pawls (
) make a click sound.
CAUTION:
• Place the grommet on the floor, then fasten it in place from
below the vehicle.
• Check that pulling down on the grommet does not discon-
nect it.
• Pay attention to the following when connecting the control cable to the CVT shift selector.
1.
Shift the selector lever and Manual lever to “P” position.
2.
When connecting the control cable
to the CVT shift selector
assembly
, face the grooved surface of the rib
up and insert
the control cable until it stops.
3.
Install the socket
onto the CVT shift selector assembly.
CAUTION:
• Place the socket onto the CVT shift selector assembly,
then fasten it in place from above.
• Check that the pulling on the socket does not disconnect
it.
MR20DD : Inspection
INFOID:0000000010622594
INSPECTION AFTER INSTALLATION
Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
QR25DE
: Vehicle front
JPDIA0107ZZ
JSDIA5182ZZ
JPDIA0609ZZ
JSDIA1810ZZ
CONTROL CABLE
TM-409
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
QR25DE : Exploded View
INFOID:0000000010622595
QR25DE : Removal and Installation
INFOID:0000000010622596
REMOVAL
CAUTION:
• Always apply the parking brake before performing removal and installation.
• Be careful not to cut your hand on heat insulator edges.
1.
Turn ignition switch OFF.
2.
Shift the selector lever to “P” position.
3.
Remove battery tray. Refer to
PG-148, "EXCEPT FOR R9M : Removal and Installation"
.
4.
Remove the control cable nut (
) and remove the control cable
from the manual lever
.
Control cable
Transaxle assembly
Manual lever
Bracket A
Lock plate
Bracket B
Grommet
CVT shift selector assembly
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSDIA5365GB
: Vehicle front
JSDIA4147ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст