Nissan X-Trail 32. Manual — part 496
INTELLIGENT KEY BATTERY
DLK-325
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY BATTERY
Removal and Installation
INFOID:0000000010708320
1.
Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2.
Insert remover tool (A) wrapped with a cloth into the slit of the
corner and twist it to separate the upper part from the lower part.
CAUTION:
• Never touch the circuit board or battery terminal.
• The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3.
Replace the battery with new one.
4.
Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
CAUTION:
• When replacing battery, keep dirt, grease, and other for-
eign materials off the electrode contact area.
• After replacing the battery, check that all Intelligent Key
functions work normally.
PIIB6221E
Battery replacement
:Coin-type lithium battery
(CR2032)
PIIB6222E
DLK-326
< REMOVAL AND INSTALLATION >
[TYPE 1]
BACK DOOR OPENER SWITCH ASSEMBLY
BACK DOOR OPENER SWITCH ASSEMBLY
Removal and Installation
INFOID:0000000010708321
REMOVAL
1.
Remove back door inner finisher. Refer to
INT-47, "Removal and Installation"
2.
Remove back door lock assembly. Refer to
DLK-312, "DOOR LOCK : Removal and Installation"
.
3.
Disconnect back door opener switch assembly harness connector.
4.
Remove switch cover mounting screw
.
5.
Remove grommet
, and then remove switch cover
.
6.
Press toward outside (in the direction shown by arrow) and then
remove back door opener switch assembly
.
INSTALLATION
Install in the reverse order of removal.
JMKIB2751ZZ
JMKIB2752ZZ
JMKIB2753ZZ
AUTOMATIC BACK DOOR CONTROL UNIT
DLK-327
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
AUTOMATIC BACK DOOR CONTROL UNIT
Removal and Installation
INFOID:0000000010708322
REMOVAL
1.
For 3 seat row models: Remove third seat. Refer to
SE-70, "Removal and Installation"
2.
Remove luggage side lower finisher LH. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER :
.
3.
Disconnect automatic back door control unit harness connector.
4.
Remove the automatic back door control unit mounting bolt
,
and then remove the automatic back door control unit
.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installing automatic back door control unit, perform additional service when replace control unit. Refer to
JMKIB2759ZZ
DLK-328
< REMOVAL AND INSTALLATION >
[TYPE 1]
AUTOMATIC BACK DOOR MAIN SWITCH
AUTOMATIC BACK DOOR MAIN SWITCH
Removal and Installation
INFOID:0000000010708323
REMOVAL
1.
Remove the instrument lower panel RH. Refer to
IP-41, "Removal and Installation"
2.
Remove screws
and then remove the switch bracket
from
the instrument lower panel RH.
3.
Remove automatic back door main switch
from the switch
bracket.
INSTALLATION
Install in the reverse order of removal.
JMKIB2781ZZ
: Pawl
JMKIB3654ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст