Nissan X-Trail 32. Manual — part 2181
TM-682
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
OIL PAN
3.
Remove the drain plug gasket
.
4.
Remove the oil pan bolts (
) and remove the oil pan and oil pan
gasket.
5.
Remove the oil pan gasket
from the oil pan.
6.
Remove the magnets
from the oil pan.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse oil pan gasket.
• Never reuse drain plug gasket.
• Completely clean the iron powder from the magnet area of oil pan and the magnets.
• Install the oil pan to the transaxle case with the following procedure.
1.
Install the oil pan gasket to the oil pan.
CAUTION:
Completely wipe out any moisture, oil, and old gasket from the oil pan gasket surface and bolt
hole of oil pan and transaxle case.
2.
Install the oil pan assembly to the transaxle case and temporarily tighten the oil pan bolt.
JSDIA5206ZZ
: Vehicle front
JSDIA5207ZZ
JSDIA5208ZZ
JSDIA5209ZZ
OIL PAN
TM-683
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Tighten the oil pan bolts in the order shown to the specified
torque.
4.
Tighten the oil pan bolts again clockwise from (1) shown to the
specified torque.
• Fill ATF after installation. Refer to
.
Inspection
INFOID:0000000010622888
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Check the CVT fluid leakage. Refer to
: Vehicle front
JSDIA5211ZZ
TM-684
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
INPUT SPEED SENSOR
INPUT SPEED SENSOR
Exploded View
INFOID:0000000010622889
Removal and Installation
INFOID:0000000010622890
REMOVAL
1.
Turn ignition switch OFF.
2.
Remove the battery tray. Refer to
PG-148, "EXCEPT FOR R9M : Removal and Installation"
3.
Remove the fluid cooler hose A. Refer to
4.
Remove the fluid cooler hose B and fluid cooler hose F from CVT oil warmer side. Refer to
5.
Remove the water hose A and water hose B. Refer to
6.
Disconnect the input speed sensor harness connector.
7.
Remove mounting bolt (
) and remove input speed sensor
from transaxle assembly.
Transaxle assembly
O-ring
Input speed sensor
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA5131GB
JSDIA5195ZZ
INPUT SPEED SENSOR
TM-685
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8.
Remove O-ring
from input speed sensor.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to the O-ring.
Inspection and Adjustment
INFOID:0000000010622891
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
If CVT fluid leaks during work, adjust the CVT fluid level. Refer to
.
JSDIA5196ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст