Nissan X-Trail 32. Manual — part 487
REAR DOOR
DLK-289
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4.
Disengage fixing pawl on front upper end of rear door weather-strip using a remover tool (A), and then
remove weather-strip clip.
5.
Remove rear fixing clips from weather-strip.
6.
Disengage fixing pawl on rear upper end of rear door weather-strip using a remover tool (A), and then
remove weather-strip clip.
7.
Remove door check link mounting bolt of vehicle body side.
8.
Remove rear door weather-strip from rear door panel.
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIB3092ZZ
JMKIB3093ZZ
: Pawl
JMKIB3094ZZ
DLK-290
< REMOVAL AND INSTALLATION >
[TYPE 1]
BACK DOOR
BACK DOOR
Exploded View
INFOID:0000000010708279
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010708280
CAUTION:
• Back door is made of resin. Never apply strong force to it, and be careful to prevent contact with oil.
• Perform work with 2 workers, because of its heavy weight.
• Use protective tape or shop cloth to protect from damage during removal and installation.
Back door hinge
Back door weather-strip
Bumper rubber
Wedge bracket
Back door wedge
Back door striker
TORX bolt
Back door panel
Plug
Stud ball
Back door damper
: Center mark
: Seam
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB3683GB
BACK DOOR
DLK-291
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOVAL
1.
Remove headlining. Refer to
INT-37, "Removal and Installation"
2.
Disconnect back door harness connectors
,
and
, and
then remove harness fixing clips
.
3.
Disconnect harness connector
, and then remove harness fix-
ing clips
.
4.
Remove grommet
from roof panel
, and then pull out back
door harness from vehicle body.
5.
Remove air tube
from tube clip
, and then disconnect tube
joint connector
and air tube
(with around view monitor).
: Vehicle front
JMKIB3115ZZ
: Vehicle front
JMKIB3116ZZ
JMKIB3117ZZ
: Vehicle front
JMKIB3118ZZ
DLK-292
< REMOVAL AND INSTALLATION >
[TYPE 1]
BACK DOOR
6.
Remove tube grommet
from roof panel
, and then pull out
air tube from vehicle body.
7.
Disconnect rear washer tube A and rear washer tube B. Refer to
.
8.
Disconnect rear view camera washer tube (with around view monitor). Refer to
.
9.
Remove tube grommet
from roof panel
, and then pull out
rear washer tube B and rear camera washer tube from vehicle
body.
10. Support back door with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
11. Remove spindle unit from back door. Refer to
DLK-313, "SPINDLE UNIT : Removal and Installation"
.
12. Remove back door hinge mounting nuts of back door and remove back door assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• After installation, perform the fitting adjustment. Refer to
DLK-293, "BACK DOOR ASSEMBLY :
• After installation, check whether harness is not pinched. If harness is pinched, pull harness down-
ward lightly.
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• After installation, check that door opens and closes normally. Refer to
BACK DOOR ASSEMBLY : Inspection
INFOID:0000000010708281
1.
Open and close the back door. Check that door hinge rotation portion moves smoothly.
JMKIB3119ZZ
JMKIB3120ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст