Nissan X-Trail 32. Manual — part 1258
FAX-24
< REMOVAL AND INSTALLATION >
[2WD]
FRONT DRIVE SHAFT BOOT
14. Clean the matching surface of drive shaft and wheel hub and
bearing assembly. And then apply paste [service parts
(440037S000)] to surface
of joint sub-assembly of drive shaft.
CAUTION:
Apply paste to cover entire flat surface of joint sub-assem-
bly of drive shaft.
15. Insert drive shaft to wheel hub and bearing assembly, and then temporarily tighten wheel hub lock nut.
CAUTION:
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
16. Install transverse link to steering knuckle and front suspention member. Refer to
.
17. Install steering outer socket to steering knuckle.
• LHD: Refer to
• RHD: Refer to
.
18. Tighten the wheel hub lock nut to the specified torque. Refer to
CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel
hub lock nut.
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
19. When installing a cotter pin
and adjusting cap
, securely
bend the basal portion to prevent rattles.
CAUTION:
Never reuse cotter pin.
20. Install disc rotor. Refer to
FAX-11, "Removal and Installation"
21. Install caliper assembly to steering knuckle.
• LHD (1 PISTON TYPE): Refer to
BR-51, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• LHD (2 PISTON TYPE): Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
• RHD (1 PISTON TYPE): Refer to
BR-111, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• RHD (2 PISTON TYPE): Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
22. Install lock plate to strut assembly.
• LHD: Refer to
BR-24, "FRONT : Exploded View"
.
• RHD: Refer to
BR-88, "FRONT : Exploded View"
23. Install wheel sensor to steering knuckle. Refer to
BRC-212, "FRONT WHEEL SENSOR : Removal and
.
24. Install tires to vehicle.Refer to
WT-61, "Removal and Installation"
25. Perform inspection after installation. Refer to
.
Transaxle Side
• Installation: Refer to
FAX-36, "MR20DD : Removal and Installation"
.
Amount paste
: 1.0 – 3.0 g (0.04 – 0.10 oz)
JPDIG0122ZZ
JPDIF0295ZZ
FRONT DRIVE SHAFT BOOT
FAX-25
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Assembly: Refer to
FAX-42, "MR20DD : Disassembly and Assembly"
MR20DD : Inspection
INFOID:0000000010824383
INSPECTION AFTER REMOVAL
Check the following items, and replace the part if necessary.
• Check components for deformation, cracks, and other damage.
• Check boots of transverse link and steering outer socket ball joint for breakage, axial end play, and swing
torque.
- Transverse link: Refer to
.
- Steering outer socket: Refer to
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
BRC-212, "FRONT WHEEL SENSOR :
.
2.
Check the wheel alignment. Refer to
.
3.
Adjust neutral position of steering angle sensor. Refer to
.
R9M
R9M : Exploded View
INFOID:0000000010824384
LEFT SIDE
JSDIA5389ZZ
Circular clip
Dust shield
Housing
Snap ring
Spider assembly
Stopper ring
Boot band
Boot
Shaft
Damper band
Dynamic damper
Joint sub-assembly
Dust shield
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
: Always replace after every disassembly.
FAX-26
< REMOVAL AND INSTALLATION >
[2WD]
FRONT DRIVE SHAFT BOOT
RIGHT SIDE (CVT)
JSDIA6127GB
Dust shield
Joint sub-assembly
Circular clip
Boot band
Boot
Shaft
Damper band
Dynamic damper
Stopper ring
Spider assembly
Snap ring
Housing
Dust shield
Support bearing
Retainer
Support bearing bracket
Heat insulator
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
FRONT DRIVE SHAFT BOOT
FAX-27
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
RIGHT SIDE (M/T)
R9M : Removal and Installation
INFOID:0000000010824385
REMOVAL
Wheel Side
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove wheel sensor from steering knuckle. Refer to
BRC-212, "FRONT WHEEL SENSOR : Removal
JSDIA6125GB
Dust shield
Joint sub-assembly
Circular clip
Boot band
Boot
Shaft
Stopper ring
Spider assembly
Snap ring
Housing
Dust shield
Support bearing
Retainer
Support bearing bracket
Heat insulator
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст