Nissan X-Trail 32. Manual — part 1054
CYLINDER BLOCK
EM-113
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Install the connecting rod bearings in the center of connecting rod and connecting rod cap as shown in
the figure. For service operation, the center position can be checked, visually.
10. Install piston and connecting rod assembly to crankshaft.
• Position crankshaft pin corresponding to connecting rod to be installed onto the bottom dead center.
• Apply new engine oil sufficiently to the cylinder bore, piston and crankshaft pin.
• Match the cylinder position with the cylinder number
on
connecting rod to install.
• Install so that front mark
on the piston head faces the front
of engine.
• Using a piston ring compressor [SST: EM03470000]
or suit-
able tool, install piston with the front mark on the piston head
facing the front of the engine.
CAUTION:
Be careful not to damage the cylinder wall and crankshaft
pin, resulting from an interference of the connecting rod
big end.
11. Install connecting rod cap.
• Match the stamped cylinder number marks
on connecting
rod with those on connecting rod cap to install.
12. Tighten connecting rod cap bolt with the following procedure:
CAUTION:
• Check that there is no gap in the thrust surface
of the
joint between connecting rod
and connecting rod cap
and that these parts are in the correct position. And
then, tighten the connecting rod cap bolts.
• If the connecting rod cap bolts are reused, measure the
outer diameter. Refer to
a.
Apply new engine oil to the threads and seats of connecting rod
cap bolts.
b.
Tighten connecting rod cap bolts.
c.
Completely loosen connecting rod cap bolts.
: Oil hole
: Management code
: Big end diameter grade
: Front mark (connecting rod cap)
JPBIA4434ZZ
PBIC3244J
: Front mark (piston)
: Oil hole
: Management code
: Big end diameter grade
: Front mark (connecting rod cap)
JPBIA4434ZZ
: 27.5 N·m (2.8 kg-m, 20 ft-lb)
PBIC3510J
EM-114
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
CYLINDER BLOCK
d.
Tighten connecting rod cap bolts.
e.
Then turn all connecting rod cap bolts 60 degrees clockwise (angle tightening).
CAUTION:
Check and confirm the tightening angle by using an angle
wrench [SST: KV10112100]
or protractor. Never judge by
visual inspection without the tool.
• After tightening connecting rod cap bolt, check that crankshaft rotates smoothly.
• Check the connecting rod side clearance. Refer to
13. Install oil pan (upper). Refer to
.
NOTE:
Install the rear oil seal after installing the oil pan (upper).
14. Install rear oil seal. Refer to
EM-90, "REAR OIL SEAL : Removal and Installation"
15. Install drive plate. Refer to
EM-65, "Removal and Installation"
16. Install knock sensor.
• Install knock sensor
with harness connector facing toward
the rear of engine.
CAUTION:
• Never tighten mounting bolts while holding the harness
connector.
• If any impact by dropping is applied to knock sensor,
replace it with a new one.
NOTE:
• Check that there is no foreign material on the cylinder block mating surface and the back surface of
knock sensor.
• Check that knock sensor does not interfere with other parts.
17. Install crankshaft position sensor (POS) and crankshaft position sensor (POS) cover.
CAUTION:
• Handle crankshaft position sensor (POS) carefully and avoid impacts.
• Never disassemble.
• Never place crankshaft position sensor (POS) in a location where it is exposed to magnetism.
: 0 N·m (0 kg-m, 0 ft-lb)
: 19.6 N·m (2.0 kg-m, 14 ft-lb)
PBIC3245J
: Cylinder block left side
: Engine front
JPBIA5163ZZ
CYLINDER BLOCK
EM-115
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
18. Install oil filter (for intake valve timing control)
in the direction
shown in the figure.
• Check that the oil filter (for intake valve timing control) does
not protrude from the upper surface of cylinder block
after
installation.
19. Assemble in the reverse order of disassembly.
Inspection
INFOID:0000000010783734
CRANKSHAFT END PLAY
• Measure the clearance between thrust bearings and crankshaft
arm when crankshaft is moved fully forward or backward with a dial
indicator (A).
• If the measured value exceeds the limit, replace thrust bearings,
and measure again. If it still exceeds the limit, replace crankshaft
also.
CONNECTING ROD SIDE CLEARANCE
• Measure the side clearance between connecting rod and crank-
shaft arm with a feeler gauge (A).
• If the measured value exceeds the limit, replace connecting rod,
and measure again. If it still exceeds the limit, replace crankshaft
also.
PISTON TO PISTON PIN OIL CLEARANCE
Piston Pin Hole Diameter
Measure the inner diameter of piston pin hole with an inside
micrometer (A).
Piston Pin Outer Diameter
PBIC3260J
Standard and Limit
: Refer to
.
JSBIA2509ZZ
Standard and Limit
: Refer to
.
JPBIA0689ZZ
Standard
: Refer to
.
JSBIA2510ZZ
EM-116
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
CYLINDER BLOCK
Measure the outer diameter of piston pin with a micrometer (A).
Piston to Piston Pin Oil Clearance
(Piston to piston pin oil clearance) = (Piston pin hole diameter) – (Piston pin outer diameter)
• If oil clearance is out of the standard, replace piston and piston pin assembly.
• When replacing piston and piston pin assembly. Refer to
.
NOTE:
• Piston is available together with piston pin as assembly.
• Piston pin (piston pin hole) grade is provided only for the parts installed at the plant. For service parts, no
grades can be selected. (Only grade “0” is available.)
PISTON RING SIDE CLEARANCE
• Measure the side clearance of piston ring and piston ring groove
with a feeler gauge (A).
• If the measured value exceeds the limit, replace piston ring, and
measure again. If it still exceeds the limit, replace piston also.
PISTON RING END GAP
• Check that cylinder bore inner diameter is within specification. Refer to “PISTON TO CYLINDER BORE
CLEARANCE”.
• Lubricate with new engine oil to piston
and piston ring
, and
then insert
piston ring until middle of cylinder
with piston, and
measure piston ring end gap with a feeler gauge (C).
• If the measured value exceeds the limit, replace piston ring, and
measure again. If it still exceeds the limit, rebore cylinder and use
oversized piston and piston rings.
CONNECTING ROD BEND AND TORSION
Standard :
Refer
JSBIA2511ZZ
Standard :
Standard and Limit
: Refer to
JSBIA2512ZZ
Standard and Limit
: Refer to
JSBIA2513ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст